Bedienungsanleitung Campingaz Comfort Heat CR - CR 5000 Comfort (Seite 10 von 59) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

662400

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

E - 1 - Igniting the appliance

Note: Gas opening and closing controls are located on

gas bottle and/or on pressure reducing valve.

Ignition spark, gas inlet control and temperature or

power controls are actuated from the control panel

located in the appliance top right section (fig. 1 item 1)

and (fig. 5 items A, B and C).

1- Open bottle cock and/or pressure reducing valve

handle and carry out a leak test.

2-a-Comfort Heat CR Version

- Do not place the heater just below an electric socket.

- Do not use the heater near a bath, shower or

swimming pool.

Set handle (A) to position ( ▼ ) and press the handle

for 10 seconds to allow the gas to reach the pilot

burner (fig. 5).

2-b-Comfort Heat CR Thermo Version

Set handle (C) to the maximum position and

press control button (

▼) for 10 seconds to allow

the gas to reach the pilot burner (fig. 5).

3- Push the flame ignition button (B) located next to

the (

) symbol) all the way down several times

while simultaneously holding down the handle

(A) or the control button (A) for 10 seconds. The

thermocouple is activated and the safety valve

does not cut off gas feed. Release button A or

handle A.

4- Check whether the appliance did light up. If not,

repeat the procedure from step 2).

5- The appliance must be held in maximum position

for about 10 minutes in order to fully activate the

catalytic panel.

Note: Some air may be trapped in the gas line. This

will prevent the appliance from lighting up during the

first attempt. In this case, it is necessary to repeat the

ignition procedure several times until the safety pilot

burner lights up.

During appliance operation, the safety pilot burner

must remain permanently lit in order to ensure correct

operation of the atmosphere analyser.

During the first setting to service, operate the appliance

at maximum power for at least 15 minutes in order

to eliminate the typical new appliance smell due to

the presence of protecting substances applied to the

component parts.

Ventilate the room during this operation.

E - 2 - Setting temperature or power (Fig. 5)

Your appliance is equipped with a setting handle which

makes it possible to adjust the temperature radiated

by the catalytic panel depending on the temperature

desired in the room.

a) Comfort Heat CR Version

Set the heating temperature by positioning handle index

between positions (

) and ( )(3: see fig. 5 -

Comfort Heat CR - item A)

b) Comfort Heat CR Thermo Version

To adjust heating temperature, position the adjustment

button(C)betweenthemaximum(▼)andminimum

levels (6 positions: see fig. 5 - Comfort Heat CR

Thermo - letter C).

E - 3 - Shutting down the appliance

Close bottle cock and/or gas pressure reducing valve

handle.

THIS APPLIANCE IS EQUIPPED WITH AN

ATMOSPHERE ANALYSER DEVICE WHICH

AUTOMATICALLY TURNS OFF THE APPLIANCE

SHOULD THE ROOM CONTAIN TOO HIGH A

CARBON DIOXIDE PERCENTAGE (CO

2).

IN THIS CASE, THOROUGHLY VENTILATE THE

ROOM, OTHERWISE THE APPLIANCE WILL NOT

RELIGHT.

F - REMOVING OR REPLACING THE GAS

BOTTLE

- Check that gas bottle cock and/or pressure reducing

valve handle is in the closed position.

- Open appliance rear plate (fig. 4 item B) and remove

the bottle from its housing, taking care not to pull or

bend the hose.

- Disconnect pressure reducing valve from gas bottle.

- Install the new gas bottle and carry out a leak test as

described under paragraphs D-1 and D-2.

G - STORAGE - SERVICING

1) Appliance

When it is not used, the appliance should remain open

and be stored in a dust-free place.

- Remove stains with soapy water, when the appliance

is cold. Wipe off with a cloth.

- Do not use abrasives which might damage the

paintwork.

- For heavy repairs, please call your vendor.

- The appliance must be periodically checked, more

particularly concerning condition of the connecting

hose.

2) Hose between the pressure reducing valve

and the appliance

- Periodically check hose for condition and replace it if it

displays ageing signs or cracks.

- The hose must be replaced by a new one of same

length and equivalent quality.

- The hose must be replaced in compliance with

the above-mentioned periodicity for the respective

countries.

- In France, if the expiry date printed on the hose is

reached, it must be replaced by a hose compliant with

the XP D 36-112 Standard.

- Comply with installation indications provided with these

new assemblies to be 0.50 m long, and with the

procedure described under paragraph C-2.

- If your appliance is to remain unused for a long period,

disconnect gas bottle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Campingaz Comfort Heat CR - CR 5000 Comfort Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info