Bedienungsanleitung Campingaz CR 5000 Turbo (Seite 9 von 71) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

662399

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

E - UTILISATION

OPERATING PRECAUTIONS

DO NOT install the appliance next to a wall,

curtains or a sofa or armchair.

DO NOT cover the appliance with clothes or other

objects.

DO NOT move the appliance when in operation.

The appliance must ALWAYS be directed to the

centre of the room.

The appliance must be put in a dry place.

This appliance protecting grid is designed to

prevent fire hazards or burns and no part shall be

permanently removed.

THE GRID DOES NOT TOTALLY PROTECT YOUNG

CHILDREN OR THE DISABLED.

E - 1 - Igniting the appliance

Note: Gas opening and closing controls are located on

gas bottle and/or on pressure reducing valve.

Ignition spark, gas inlet control and temperature or

power controls are actuated from the control panel

located in the appliance top right section (fig. 1 item 1)

and (fig. 5 items A, B and C).

1- Open bottle cock and/or pressure reducing valve

handle and carry out a leak test.

2-a-CR 5000 Version and CR 5000 Turbo Versions

Electrically connect the CR 5000 Turbo Version.

Caution: The appliance was designed to be supplied

with a 230 V 50 Hz voltage. Your installation must be

equipped with a grounding connection compliant

with electrical systems specifications in force.

- Do not place the heater just below an electric socket.

- Do not use the heater near a bath, shower or

swimming pool.

Set handle (A) to position (START) and press the

handle for 10 seconds to allow the gas to reach the

pilot burner (fig. 5).

2-b-CR 5000 Thermo Version

Set handle (C) to the maximum position (IIII) and

press control button (A) for 10 seconds to allow the

gas to reach the pilot burner (fig. 5).

3- Fully press several times the LH button marked with

a stylised lightning (

) (B) for lighting up the

flame, while holding handle (A) or control button (A)

depressed for 10 seconds. The thermocouple is

activated and the safety valve does not cut off gas

feed.

Release button A or handle A.

4- Check whether the appliance did light up. If not,

repeat the procedure from step 2).

5- The appliance must be held in maximum position for

about 10 minutes in order to fully activate the catalytic

panel.

Note: Some air may be trapped in the gas line. This

will prevent the appliance from lighting up during the

first attempt. In this case, it is necessary to repeat the

ignition procedure several times until the safety pilot

burner lights up.

During appliance operation, the safety pilot burner

must remain permanently lit in order to ensure correct

operation of the atmosphere analyser.

During the first setting to service, operate the appliance

at maximum power for at least 15 minutes in order

to eliminate the typical new appliance smell due to

the presence of protecting substances applied to the

component parts.

Ventilate the room during this operation.

national regulations in force (BS, UNI, UNE, etc....).

The hose shall be 0.50 m long. It shall be replaced if

it appears to be damaged or cracked. Do not pull or

twist the hose. Keep it away from parts that are likely

to get heated.

- Check tightness in compliance with indications of

paragraph D-2.

D - CONNECTING THE GAS BOTTLE

If an empty bottle is in place, read paragraph

F-”Removing or replacing gas bottle”.

To install or remove a gas bottle, always operate

in a well-ventilated place and never in presence of

a flame, spark or heat source (cigarette, electric

appliance, etc.).

- Open appliance rear plate (fig. 1 item 3).

Note: If the appliance is new, remove the plastic cable

tie (Figure 1 number 4), lift and remove rear plate (3).

D - 1 - Installing gas bottle:

- Position the gas bottle on the floor behind the appliance.

- Check whether bottle cock and/or pressure reducing

valve handle is in “closed” position.

- Screw in or engage pressure reducing valve to gas

bottle or gas bottle cock (fig. 3 item B).

- Install gas bottle through appliance rear so that the

hose does not touch appliance metal panels and is

not excessively bent or pinched.

- Check that the hose runs normally and is neither bent

nor pulled.

- Install appliance rear plate (fig. 4 item A).

D - 2 - Tightness:

In case of leak, appliance gas supply must be

shut down using gas bottle cock and/or pressure

reducing valve handle.

Do not carry out leak tests with a flame, use a gas

leak detecting liquid.

- Apply gas leak detecting liquid to bottle/pressure

reducing valve/hose/appliance unions.

- Open the gas inlet (bottle cock and/or pressure

reducing valve handle) (fig. 4).

- If bubbles appear, this means that there are gas

leaks.

- To remove the leak, tighten hose nuts and/or hose

clamps if any. If a part is defective, have it replaced.

The appliance should not be returned to service until

the leak is removed.

- Close gas bottle cock.

Important:

In case of gas leak or odour, immediately close

bottle cock and/or pressure reducing valve handle.

Enhance room ventilation by opening the windows.

Ask a specialised technician to check the appliance

and proper bottle connection.

A leak test should be carried out at least once a year

and whenever the gas bottle is changed.

Campingaz CR 5000 Turbo Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info