Bedienungsanleitung Campingaz Gardensol Comfort (Seite 7 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

662409

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

a)Open the gas inlet at the cylinder valve and/or regulator

and/or press the regulator firing button if fitted (see regulator

notice) (fig. 13A and B).

b)Push handwheel (B) in in the direction of arrow (A) and place

it on position (Z) ( ); hold it down for 10 seconds.

c)Press the button for the piezo-electric mechanism (P) in the

direction of arrow (C) and check via hole (V) that the safety

pilot light is clearly alight, whilst continuing to hold the control

handwheel (B) down for a further 10 seconds so that the

safety system does not cut the gas supply off.

d)Let the control handwheel (B) go and place it on the heat

function in the desired position (1 ) (2 )

If the safety pilot light goes out, repeat the steps from a) to d).

- Place the handwheel (B) on the OFF position ( ) (by pres-

sing it down lightly to pass position (W).

- Proceed as indicated in the paragraph above, but instead of

pressing the piezo-electric mechanism button (P), use a ligh-

ted match in the hole (V).

- Remove the match as soon as the safety pilot light is alight.

- Air may be present in the gas circuit. This prevents the hea-

ter from lighting at the first attempt. Repeat the lighting pro-

cess several times in this case until the safety pilot light is

alight.

- When the heater is in use, the safety pilot light (V) must

always remain lit to make sure that the flame safety device is

working correctly.

- The burner will turn black after the first use; this is perfectly

normal and in no way reduces its performance.

The heater has two safety devices:

1) The "extinguishing safety device" automatically shuts off the

gas flow to the heater burner if this goes out accidentally.

2) The "tipping safety device" automatically shuts off the flow of

gas to the heater if it is leaning at more than 45° from the ver-

tical or if it has tipped over onto the ground.

- Check that the cylinder valve and/or the regulator lever is in

the off position.

- Raise the cylinder cover so that the gas cylinder is totally free

and unhook the safety belt using the clip (M) (fig. 16).

- Disconnect the regulator from the gas cylinder.

- Remove the gas cylinder from the heater base

- Position the new gas cylinder

- Connect the regulator to the gas cylinder. Check the regula-

tor seal. (Make sure that the regulator seal is installed cor-

rectly and able to fulfil its function).

- Put the safety strap back and lower the cylinder cover right

down.

- Do not obstruct the ventilation ports in the cylinder housing.

- Check the state of the flexible hose.

- Shut down the equipment as indicated in paragraph 3-1-2

- Close the gas inlet (cylinder valve (fig. 13A) and/or regulator

lever (figure 13B)).

- Check that the safety strap is holding the gas cylinder firmly

in its housing.

- Tilt the equipment backwards until supported by the wheels

and move it slowly. (fig. 18)

- Check the state of the flexible hose once a month and repla-

ce it if it shows signs of ageing or surface cracks.

- Replace the flexible hose with a new hose of the same length

and equivalent quality.

- The flexible hose (whether pre-fitted with endpieces or not)

should be replaced according to the timescale indicated

above depending on the country.

- Check for leaks as described in section 2 § 4.

- Check that the gas is shut off on the gas cylinder (cylinder

valve and/or regulator lever in off position).

- Store the heater and its gas cylinder in a cool, dry and venti-

lated area, out of reach of children, and never in a basement

or cellar. The propane gas cylinder should be stored away

from living quarters or their outbuildings. For extended stora-

ge of the heater: remove the cylinder from the heater

- If the injector clogs (the cylinder still contains gas but the hea-

ter does not light), do not attempt to unclog it but take the

heater to your retailer.

The product is covered by a total parts and labour warranty for

2 years with effect from the purchase date, excluding return

transport charges that should be borne by the consumer. The

warranty applies when the delivered product does not conform

to the order or is defective, from the moment that the claim is

accompanied by proof of purchase date (e.g. invoice, till

receipt). The product should be returned carriage paid, com-

plete and assembled, to an authorised after-sales service cen-

tre, with the claim describing the nature of the problem. A pro-

duct for which a claim is being made may be repaired, repla-

ced or reimbursed, in full or partially. The warranty is null and

void and does not apply if the damage is caused by (i) incor-

rect product use or storage, (ii) defective product maintenance

or maintenance that fails to comply with the instructions for

use, (iii) repair, modification or servicing of the product by

unauthorised third parties, (iv) the use of non-original spare

parts.

Gordano Gate Wyndham Way - Portishead

BRISTOL BS20 7GG ENGLAND

01275 845 024 / Fax: 01275 849 255

WARNING: Due to our policy of continual product development, the company reserves the right to alter or modify this

product without prior notice.

Web site: www.campingaz.com

GB.qxp 10/01/2006 15:14 Page 2

Campingaz Gardensol Comfort Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info