Bedienungsanleitung Camry CR 7810 (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

734438

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

After power on the device press mode switch (H) on the control panel (4) to select desired power level 800W or 1200W or 2000W by

repeated pressing. The display (3) will light up indicator A or B or C.

2. Make sure that all controls are set to off position. Connect the oil heater to mains power, press the power switch on (2) and then

press power on button (G) to start operation, press both again to stop operation. To turn off the device, press the power button (G) and

then press the power switch (2).

USING THE DEVICE

3. Power level setting

4. Temperature setting

1. Place the oil heater a minimum of 100 cm from walls, furniture, curtains, plants etc. on a flat and stable surface.

CAUTION: During first use of the heater a small amount of smoke may appear. This is normal.

A.– low power level 800W indicator B.– medium power level 1200W indicator

1.Carry handle 2..Safety power switch 3.Display:

C.– high power level 2000W indicator D.– heating mode indicator

WARNING: To avoid overheating do not cover the heater.

DESCRIPTION OF THE DEVICE (Figure 1)

sink filled with water.

22. The heater is filled with a set amount of special oil. Repairs requiring opening of the oil

container must be carried out only by the manufacturer or authorized representative, who

should be contacted if oil leaks from the heater.

23. If disposing of the heater please follow rules of oil disposal.

16. The power cable should not be placed above the heater, and also should not touch or

lie close to hot surfaces. Do not place the heater under an electrical outlet.

17. The surface of the heater can heat up to high temperatures of over 60 degrees C. Take

care when near the heater.

15. The heater should be placed on a level, heat-resistant surface, away (at least one

meter) from flammable materials (lace curtains, curtains, wallpaper, furniture etc.).

18. Do not cover the heater with curtains, a towel or hang washing on it – this can damage

the heater or cause a fire.

19. When using the heater, completely unwind its cable and make sure that the cable is not

touching the hot surface of the heater.

20. Do not use the heater near basins, showers, sinks, pools or other places where it can

get wet.

21. The device must be completely cool prior to storage. Keep the original packaging to

store the heater in during non-heating seasons.

5.Cord storage 6.Radiant ribs 7.Wheels 8.Remote control

K.– timer switch

I.– temperature increase button J.– temperature decrease button

E.– timer mode indicator F.– power indicator

4.Control panel:

1. Turn the heater upside down.

G.– power button H.– mode switch to select power level 800W / 1200W / 2000W

2. Place the wheel bases between the first two ribs and end two ribs.

4. Block the clamp by screwing on the butterfly nut.

5. Place the heater on the wheels.

CAUTION: After turning the heater, wait at least one hour before connecting it to a power outlet.

ASSEMBLY (Fig. 2)

3. Use the U-shaped clamp to hook the bases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Camry CR 7810 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info