Bedienungsanleitung Canadian Spa Company Grand Rapids 2021 (Seite 6 von 9) (Englisch)

764890

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

GRAND RAPIDS SPA

PART 5: USAGE

Press the ‘Up’ and ‘Down’ arrows to set desired temperature, and press heat to start the heater. Place lid on the

spa while heating. It can take 24-48 hours for your spa to reach its set temperature. See Part 4 for complete list of

Control Functions.

Lock the Buckle

Push the square pad upwards to lock and downwards to unlock.

Cleaning / Replacing Filter Cartridge

WARNING: RISK OF ELECTRIC SHOCK. Unplug the PCU before beginning spa maintenance.

NOTE: A dirty or incorrect lter cartridge may contaminate the spa water and cause

damage to the heating function.

1. Carefully thread the two inlet/outlet caps on inner spa wall. (Ensure the rubber gaskets are in

place within the plastic caps)

2. Remove lter housing lid by turning it anti-clockwise, then remove the lter cartridge.

3. Rinse off lter cartridge with water and reuse if possible. Remove and clean the white lter

grill (see photo opposite) - remember to replace lter grill after cleaning.

Replace lter if the cartridge remains dirty after rinsing or is badly discoloured.

4. Put the cleaned lter back into the cartridge housing and close the lid by turning it clockwise.

5. Remove caps from the two inlet/outlet caps on inner spa wall and allow water to ow into pump. Next

purge air from the air valve on the PCU. The tub is now ready for use.

PART 6: WATER MAINTENANCE

The lter cartridge should be cleaned weekly and replaced on a monthly basis, or

depending on use. A reminder (‘CHG FIL’) will appear to change the lter after 25 days.

Hold down ‘HEAT’ for 5 seconds to clear the message. Change water once a month or

depending on usage and use appropriate spa chemicals. Please pay attention to the

chemicals used and dosage. Spa damage resulting from misuse of chemicals is not

covered by the warranty.

Water Balance: We recommend you maintain your water balance: PH value: 7.2 - 7.6;

Free Chlorine: 2ppm - 3ppm; Alkalinity: 120-150ppm. Use a test kit to test your spa

water before each use of the spa, or at least once per week.

Water Sanitation: We recommend using Chlorine Granules to disinfect the spa water.

Spa Ball: We suggest you use a Spa Ball to help in the ltration of your spa.

Cleaning the Spa: Clean the spa with soap and water, then rinse.

Leave it outside to dry.

Repairs: Small holes or punctures can be repaired with the

repair kit that comes with the spa (glue not included)

Maintenance & Troubleshooting

PROBLEM

Cloudy water/

Foamy water

Odour

Eye skin/

irritation

POSSIBLE CAUSE

• High pH (test to verify)

• Poor ltration

• High dissolved solids

• High level of organic

contaminants

• Low pH and/or alkalinity

combined Chlorine due to

organic contamination

SOLUTION

• Add pH down

• Add Foam Free

• Empty spa and re-ll

• Increase the amount of

Chlorine

• Add PH Booster

• Increase the amount of

Chlorine Granules

FREE

Water

Test

App

NOTE:

• The massage system will stop automatically after 30 minutes of operation. You can re-activate the jet

function by pressing the ‘JETS’ button. NOTE: Heater will automatically turn on when jets turn off.

• Heating and jet function cannot be activated at same time. When heating system is working, pressing the

‘JETS’ button will change heating mode into jet mode: heating and ltering are shut down, jet system is

activated. When jets are turned off, heating and ltering automatically resumes.

NOTE: Keeping jets on for a long period of time may cause spa water to lose heat.

• Pressing ‘HEAT’ activates the heating and ltering system at the same time. The ‘HEAT’ button will display

a solid red light as spa water heats up. Once desired temperature is reached, the heater will go into standby

mode, which will be indicated with a ashing red light.

NOTE: Heater will not resume until spa water drops 2 degrees below set temperature for maximum

efciency. You can also manually restart the heater by pressing ‘HEAT’ when heater is turned off.

Jets Massage System

‘JETS’ Button: Press the ‘JETS’ button to activate the Jet Massage System on the spa. Pressing once will start

the lowest speed of the jets (L-1 will display on the screen). Press again to increase the speed of the jets to L-2, and

press again to reach the highest jet speed, L-3. Hold down the ‘JETS’ button for 5 seconds to turn jets off. When jets

turn off, ‘FIL’ will display on the screen to indicate the ltration and heat is back on. When jets mode is on it will ick

between the speeds (l-1, 2 & 3 & BUB).

NORMAL 41ºC 42ºC

L-1 L-2 L-3 FIL

Temp and Over-heat

cycle 41ºC and 42º C

‘Temp up’ Button: Press the ‘Temp’

up button for 5 seconds and hold and

temp will raise to 41ºC or 42ºC the

next cycle it will go back to the max

temp of 40ºC on the following cycle.

(10) (11)

GRAND RAPIDS SPA

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canadian Spa Company Grand Rapids 2021 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info