Bedienungsanleitung Canadian Spa Company Saskatoon (Seite 8 von 12) (Englisch)

764892

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

OKANAGAN/SASKATOON/GANDER/MUSKOKA SPAS

MVP260 Control Reference Card

Initial Start-up

When your spa is rst actuated, it will go into Priming mode, indicated by “ .” Please see the M-7 Installation Instruction Manual

for complete instructions on Power-up and Pump Priming. The Priming mode will last for less than 5 minutes (warm to skip

Priming Mode) and then the spa will begin to heat up and maintain the water temperature in the Standard mode.

Temp/Set (80°F - 104°F / 26°C - 40°C)

The start-up temperature is set at 100F°/37°C. The last

measured temperature is constantly displayed on the LCD.

Note that the last measured spa temperature displayed is

current only when the pump has been running for at least

2 minutes.

To display the set temperature, press the warm pad once.

To change the set temperature, press the pad a second time

before the LCD stops ashing. Each press of the “warm or cool

button pad will to either raise or lower the set temperature.

After three seconds, the LCD will stop ashing and display the

current spa temperature.

Jets

Touch the “Jets” button once to activate the low speed of the

pump and again for the high speed. Press the “Jets” button

again to turn off the pump. If left running, the low speed of

the pump will automatically turn off after 4 hours, and the high

speed will automatically turn off after 15 minutes. The low

speed of the pump runs when the blower is on. It may also

activate for at least 2 minutes every 30 minutes to detect the

spa temperature and then to heat to the set temperature if

needed, depending upon mode. When the low speed turns on

automatically, it cannot be deactivated from the panel;

however, the high speed may be started.

Light

Press the “Light” button to turn the light on and off. If left on,

the light automatically turns off after 4 hours.

Mode

Mode is changed by pressing the “warm” button, then pressing

the “Light” button.

Standard Mode is programmed to maintain the desired

temperature. Note that the last measured spa temperature

displayed is current only when the pump has been running for

at least 2 minutes. “ST ” will be displayed momentarily when

you switch into Standard Mode.

Economy Mode heats the spa to the set temperature only

during lter cycles. “EC” will display solid when temperature is

not current, and will alternate with temperature when

temperature is current.

Sleep Mode heats the spa to within 20°F/10°C of the set

temperature only during lter cycles. “SL ” will display solid

when temperature is not current, and will alternate with

temperature when temperature is current.

Preset Filter Cycles

The rst lter cycle begins 6 minutes after the spa is

energized. The second lter cycle begins 12 hours later. Filter

duration is programmable for 2, 4, 6, 8 hours or for continuous

ltration (indicated by “ ”). The default lter time is 2 hours.

To program, press “warm button then “Jets.” Press “warm to

adjust. Press “Jets” to exit programming.

Freeze Protection

If the temperature sensors detect a drop to below 44°F/6.7°C

within the heater, the pump and blower will automatically

activate to provide freeze protection. The equipment stays on

until 4 minutes after the sensors detect that the spa

temperature has risen to 45°F/7.2°C or higher. In colder

climates, an optional additional freeze sensor may be added

to protect against freeze conditions that may not be sensed

by the standard sensors. Aux freeze sensor protection acts

similarly except with the temperature thresholds determined by

the switch and without a 4-minute delay in turnoff. See your

dealer for details.

(8)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canadian Spa Company Saskatoon Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info