Bedienungsanleitung Canadian Spa Company SF Series - Kingston (Seite 11 von 76) (Deutsch, Englisch, Französisch)

764901

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Starting your hot tub/spa

POWERING UP YOUR SPA

Once the spa is properly wired and ﬁlled with water, the spa power can

be turned on and Start-up chemicals added.

1. Turn on RCD breaker. If breaker trips immediately check

wire connections. Upon initial power up, 4 sets of numbers ﬂash

on the LED display of the topside Console. The last number in the

sequence is the incoming power meter which can be used to verify

that the spa is wired correctly.

2. The spa begins an automatic priming routine which will last 5

minutes (“Pr” is on the LED display).

3. The priming routine will automatically run each spa pump to

prime. When the “Pr” is displayed, press any PUMP button

to prime that pump or wait for the priming routine to turn

on the Pump. IMPORTANT: To avoid pump damage, do not run

pumps for more than 1 minute without moving water. If no water

is moving, turn the power off and perform air lock procedure.

4. The Topside Console display ﬂashes “100F” then“--F” for

approximately 2 minutes to determine water temperature as it

ﬂows through the heater.

5. The default pre-set temperature is 100F The last measured

temperature is constantly displayed on the LCD readout. This

temperature will be current only when the pump has been

running for at least 2 minutes. Set the desired temperature

between 80-104°F (26- 40°C) by pressing the temp button(s).

If the water temperature is below the set temperature, the spa’s

heater and heat indicator light will turn on. All features of

the Topside Console will be available. The spa will heat

approximately 1° every 30 minutes per 1,000 litres.

6. Check for leaks! Although spas are fully checked at the factory,

shipping & delivery might cause a leak. Remember to pay

particular attention to barrel unions adjoining the heater.

Contact your Canadian Spa dealer directly if there is a problem.

If your new spa pump does not prime (ﬂow) on the initial start-up you

may be experiencing an “air lock”.

This normal occurrence can be easily corrected by loosening the

plumbing union on the suction side of the Jet or Circulation Pump until

water ﬂows into the pump and all air is expelled.

PRESS BUTTONS SLOWLY FOR FIRST RUN WHEN STARTING UP

ONCE PR EXITS, SET TEMPERATURE ON SPA (SEE SPA OPERATION

SECTION FOR DIFFERENT SPA TOPSIDES)

The above photograph refers to plug

and play models only

Installation & Setup

PRE-DELIVERY SETUP

A standard Canadian Spa Company hot tub will be delivered to your curb, standing on its side and securely strapped to a pallet (the

swim spa models will arrive via ﬂatbed truck). Ensure that you will have sufﬁcient means to move your spa to your desired location

(dolly, forklift, crane etc). The spa cannot be disassembled and will require sufﬁcient clearance to move it (refer to table below for spa

dimensions).

Failure to properly locate your spa may void your warranty, please contact your local Canadian Spa Company Dealer if you have any questions.

Owners Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canadian Spa Company SF Series - Kingston Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info