Bedienungsanleitung Canadian Spa Company Toronto (Seite 12 von 32) (Englisch)

764874

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Owners Manual

Installation: Electrical requirements

ELECTRICAL REQUIREMENTS FOR SWIM SPA (EUROPE)

Your swim spa runs on 230V 50Hz single phase. There are two

conﬁgurations you can run your swim spa on.

The minimum supply current is 50 amps, in this conﬁguration the

heater will disengage if all 4 pumps are turned on.

The second option is to have the heater on even when the spa is

running at full speed; in very cold climates this may be desirable

especially if using the spa outdoors in winter continually. In this

conﬁguration a 60 amp supply is required.

The size of the wire required will be determined by the distance to

the supply and the shielding method; your electrician will be able to

advise you of the required wiring for your speciﬁc situation.

Access

The Swim spa will arrive assembled as a single unit on a pallet. It will

weigh approx one metric ton and cannot be disassembled. For this

reason you will need to have a crane or other mechanical method of

unloading the spa and getting it to your chosen site.

We recommend you book a contract lift where the lifting company

will assess the situation and method of lift and carry insurance in

case of accidental damage to the spa or the property. The spa

warranty does not cover damage from installation. It is the

responsibility of the customer or his agents be it crane company or

lift operator to assess the lift and control all aspects of the moving

of the spa. Canadian Spa Company will not take responsibility for

any part of the moving of the spa, and cannot advise on the methods

used to move the spa.

Base

The base for your swim spa must be a ﬂat level surface that contacts

the entire base of the spa. We recommend 15 cm of re-enforced

concrete but any ﬂat level base that is stable and will not shift or

settle will sufﬁce. If sinking your spa into the ground you need to

provide adequate drainage for water so that the hole the spa sits in

cannot ﬂood as this will damage the electronics and electrical

components. Also at least a metre of access to the entire front of the

spa ﬁlters is required for component access. You are responsible for

providing adequate access in order to repair the spa in case of fault.

CIRCUIT BOARD CODES:

E = 1 x Earth Screw

S = 7 x Standard Screws

H1 = Heater Connection ‘1’

H2 = Heater Connection ‘2’

SA = Sensor Port ‘A’

SB = Sensor Port ‘B’

T-Pad 1/2/3 = Topside Ports 1, 2 & 3

(Molex Connector)

JUMPER:

J8 = Jumper on 1 pin when using 2kW

or 1kW Heater. Jumper on 2 pin when

using 3kW Heater

J91 = Jumper on 1 pin enables Real

Time Clock function (ML900), Jumper

on 2 pin disables RTC function

1-Spd P2

Blank

Mp3

2-Spd P1

Not Used Ozone

Light

T-pad 1 T-pad 2T-pad 3

3a Light Fuse

30a Pump 1 Fuse

2a Mp3 Fuse

10a Blower Fuse

30a Pump 2 Fuse

SA SB

J91

J59

J36

J58

55596 c/board

NanswGL2km3 Circuit Board (Swim spa models: St Lawrence 13’ and 16’ Swim Spa)

Expander Board - 55026: for pump 3

&4 (split plug)

Pump 3 & 4

30 A Pump fuse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canadian Spa Company Toronto Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canadian Spa Company Toronto

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info