Bedienungsanleitung Canadian Spa Company Vancouver KH-10032 (Seite 15 von 24) (Englisch)

764896

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

VANCOUVER

Spa Functions

Pumps

Press the “Jets 1” button once to turn pump 1 on or off, and to

shift between low- and high-speeds if equipped. If left running,

the pump will turn off after a time-out period. The pump 1

low-speed will time out after 30 minutes. The high-speed will

time out after 15 minutes.

The low-speed of pump 1 runs when the other pump is on. If

the spa is in Ready Mode, Pump 1 low may also activate for at

least 1 minute every 30 minutes to detect the spa temperature

(polling) and then to heat to the set temperature if needed.

When the low-speed turns on automatically, it cannot be deac-

tivated from the panel, however the high speed may be started.

Filtration and Ozone

Pump 1 low and the ozone generator will run during ltration.

The system is factory-programmed with two lter cycles that

will run 10 minutes after power-up. The lter duration is

programmable. At the start of each lter cycle, Pump 2 will run

briey to purge its plumbing to maintain good water quality.

Freeze Protection

If the temperature sensors within the heater detect a low

enough temperature, then the pump(s) automatically activate

to provide freeze protection. The pump(s) will run either

continuously or periodically depending on conditions.

In colder climates, an optional additional freeze sensor may

be added to protect against freeze conditions that may not be

sensed by the standard sensors. Auxiliary freeze sensor

protection acts similarly except with the temperature

thresholds determined by the switch. See your dealer for details.

Clean-up Cycle

When a pump is turned on by a button press, a clean-up cycle

begins 30 minutes after the pump is turned off or times out.

The pump and the ozone generator will run for 30 minutes or

more, depending on the system.

Temperature and Temp Range

Adjusting the Set Temperature

When using a panel with Up and Down buttons (Temperature

buttons), pressing Up or Down will cause the temperature to

ash. Pressing a temperature button again will adjust the set

temperature in the direction indicated on the button. When the

LCD stops ashing, the spa will heat to the new set

temperature when required.

If the panel has a single temperature button, pressing the

button will cause the temperature to ash. Pressing the button

again will cause the temperature to change in one direction

(e.g. UP). After allowing the display to stop  ashing, pressing

the Temperature Button will cause the temperature to ash

and the next press will change the temperature in the opposite

direction (e.g. DOWN). The temperature can be set between

16°C and 40°C (60°F and 104°F).

Press-and-Hold

If a Temperature button is pressed and held when the

temperature is ashing, the temperature will continue to

change until the button is released. If only one temperature

button is available and the limit of the Temperature Range is

reached when the button is being held, the progression will

reverse direction.

PUMPS

5 HP Big Red 2 Speed pumps

Our 5 HP pump is the most powerful spa

pump in the market with our oversize

intakes.

2” Twin Roto jet

Adjustable and interchangeable jet spins

and pulsates. The jet can be removed by

turning it counter-clockwise. To replace the

jet push inward and clockwise until it clicks

into place.

3” Directional jet

Adjustable and interchangeable jet features

a directional nozzle. The jet can be removed

by turning it counter-clockwise. To replace

the jet push inward and clockwise until it

clicks into place.

3” Massage jet

Adjustable and interchangeable jet which

spins to deliver a soothing massage. The jet

can be removed by turning it counter-

clockwise. To replace the jet push inward

and clockwise until it clicks into place.

2” Directional jet

Adjustable and interchangeable jet features a

directional nozzle. The jet can be removed by

turning it counter-clockwise. To replace the jet

push inward and clockwise until it clicks into

place.

5” (Jumbo) Directional jet

Adjustable and interchangeable jet features a

directional nozzle. The jet can be removed by

turning it counter-clockwise. To replace the jet

push inward and clockwise until it clicks into

place.

5” Massage jet

Adjustable and interchangeable jet features an

internal spinner to deliver a low pressure sooth-

ing massage. The jet can be removed by turning

it counter-clockwise. To replace the jet push

inward and clockwise until it clicks into place.

2” Point jet

Standard jet is permanently on and supplies

heated water continually. The jet can be

removed by turning it counter-clockwise. To

replace the jet push inward and clockwise

until it clicks into place.

Air Controller

These are located around the top of your spa.

Increase or decrease the force of your jets by

opening or closing the air control valves.

Aroma basket cap

Open cap to place aromatherapy beads. Close

after use.

Waterfall control

Located on the topside of the spa, this valve

adjusts water ow to the waterfall.

HOW JETS WORK

Air is mixed with the water by using the air controls to create massage(s) of varying degrees. Water ow is adjusted by simply

turning the outer face of the full sized jets. Our hot tubs have a combination of pulsating, rotating, and directional adjustable jets.

(15)

Canadian Spa Company Vancouver KH-10032 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info