Bedienungsanleitung Canadian Spa Company Yukon (Seite 7 von 32) (Englisch)

764875

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Owners Manual

Locating your hot tub/spa

INDOOR LOCATION

Considerations for selecting an indoor spa location:

• Local building codes for indoor installation of a portable spa

• Adequate space for spa with accessibility for service (Clearance

of 3 ft (1m) around the spa is recommended to permit servicing

the unit)

• Proper structural support is critical. Consult a licensed

professional Structural Engineer to determine if the foundation

will adequately support the spa the entire time it will be in place,

especially if the spa is to be placed on a second story or higher,

balcony, roof or other platform not speciﬁcally tied into the main

structural support.

• Proper ventilation (Consult an Engineer or authority who

understands the necessary provisions to vent moist or heated air

and air with chemical odours. When the spa is in use

considerable amounts of moisture escapes, potentially causing

mould and mildew which can damage certain surfaces and

surroundings.

POSITIONING YOUR HOT TUB/SPA

When selecting a site for your spa, take into account the following:

A) Local Codes:

There may be certain restrictions and/or requirements that are

particular to your locality. If in doubt, check with your local council.

B) Delivery Passageway:

The spa will arrive as a unit, and cannot be disassembled. Ideally the

spa will be placed on a trolley, either on its side or on its base. The

unit will then be rolled into place easily crossing grass, gravel, and

small terrain anomalies. For safe and non-intrusive installation, we

require an opening not less than the width of your spa (see dealer

for current sizes) plus at least 40cm in height for the trolley and a

minimum of 5cm clearance on each side for adequate access. If

your access does not meet these conditions, or in the case of other

obstacles (steps, fences, walls, steep hills, etc.) contact Canadian Spa

Company for advice and conditions.

C) Location & Base:

A sheltered environment can result in lower operating and

maintenance costs. You must allow 1 metre clearance for access to

the spa’s access panel for servicing.

• The site you select for your spa MUST be a ﬂat, level continuous

surface that fully contacts the bottom of the spa.

• Your new spa weighs between 300-450kg when dry, and when

ﬁlled to capacity weighs 900-2300kg. Therefore a solid support

is essential when the spa is mounted on a deck or ground level

patio/ﬂoor. We recommend that you install your spa at ground

level. This allows easy access to equipment.

• A 10 to 15cm thick re-enforced concrete slab is ideal, but not

essential. In most cases your spa can be placed on properly

installed existing patios.

• The base must be at least the size of the bottom of your spa (see

dealer for current sizes).

• Water should always drain away from the spa. DO NOT locate

your spa in a low run-off area since melting snow or rain could

ﬂood the area and cause pump and equipment damage.

• DO NOT situate the spa near or under overhead wires and keep

clear of all electrical appliances.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canadian Spa Company Yukon Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canadian Spa Company Yukon

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info