Bedienungsanleitung Candy CDI 2212 (Seite 49 von 108) (Deutsch, Englisch, Französisch, Italienisch)

513760

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Alarm mute for the PROGRAMME

END

The alarm for the programme end may be

muted as follows:

IMPORTANT

The dishwasher must ALWAYS be off

before start of this procedure.

1. Hold down the FIRST "PROGRAMME"

button (from the right) and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME" button pressed

for at least 15 seconds (during this time,

2 audible signals will sound).

3. Release the button when the second

audible signal sounds (3 "PROGRAMME

SELECTION" indicator lights will come

on).

4. Press the same button again: the 3

indicator lights (which indicate that the

alarm is activated) will start flashing (to

indicate that the alarm is off).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To turn the alarm on again, follow the same

procedure.

Memorization of the last

programme used

The last programme used can be

memorized by following the below:

IMPORTANT

The dishwasher must ALWAYS be off

before start of this procedure.

1. Hold down the FIRST "PROGRAMME"

button (from the right) and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME" button pressed

for at least 30 seconds (during this time,

3 audible signals will sound).

3. Release the button when the THIRD

audible signal sounds (all the indicator

lights will flash).

4. Press the same button again: the

flashing indicator light (memorization off)

will stop flashing and remain on

(memorization on).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To disable the memorization, follow the

same procedure.

Fault signals

If malfunctions or faults occur when a

programme is running the indicator light

that corresponds to the selected cycle

(2 indicator lights for the "COLD RINSE"

programme) will flash rapidly and the alarm

sounds.

In this event, turn the dishwasher off by

pressing the "ON/OFF" button.

After checking to make sure the water

inlet hose tap is open, that the drain

hose is not bent and that the siphon or

filters are not clogged, set the selected

programme again.

If the anomaly persists, contact Customer

Service Department.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically discharge any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, we

recommend that the dishwasher is

not moved or tilted during operation.

If however it is necessary to tilt or

move the dishwasher, please ensure

that the washing cycle is complete

and that there is no remaining water

inside the dishwasher.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy CDI 2212 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Candy CDI 2212

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info