21
End of programme
A5 second alarm will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended. The indicator
light "WASHING" will start to flash.
Turn the programme selector to "RESET"
position, wait until the indicator light
"WASHING" goes off and press the
"ON/OFF" button.
Alarm mute for the
PROGRAMME END
The alarm for the programme end may be
muted as follows:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1. When the dishwasher is off, OPEN
the door.
2. Turn the programme selector to the
"RAPID" programme position.
3. Press the "ON/OFF" button.
4. WITHIN around 15 seconds, turn the
dial (in a clockwise direction) to the
"RESET" position and then go back to
the "RAPID" programme position again,
doing this 4 times (finishing with
programme selector on the "RAPID"
programme position).
5. The indicator light "WASHING" will
come on.
6. Turn the programme selector (in a
clockwise direction) to the "RESET"
position (the indicator light "WASHING"
will start to flash to indicate that the
alarm has been deactivated).
7. Turn off the dishwasher pressing the
"ON/OFF" button to confirm the new
setting.
To turn the alarm on again, follow the same
procedure from step 1 to 4 and when the
indicator light "WASHING" will come on,
turn the dishwasher off by pressing the
"ON/OFF" button to confirm the new
setting.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
Setting of new programme
Whenever you want to set a new programme,
you MUST turn the programme selector
to "RESET" position and wait for the
"WASHING" indicator light to go off.
Troubleshooting
While you are setting a programme, the
indicator light "WASHING" will start
flashing very quickly (and the alarm will
sound) if the electronics detect some
incorrect programming function.
In this event, turn the programme selector
to the "RESET" position, wait for the
"WASHING" indicator light to go off and
turn off the dishwasher pressing the
"ON/OFF" button.
After checking to make sure the water
inlet hose tap is open, that the drain
hose is not bent and that the siphon or
filters are not clogged, set the selected
programme again.
If the anomaly persists, contact Customer
Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
20
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
Setting a programme
WARNING!
Before setting any programme, the
programme selector must be in the
"RESET" position and the indicator
light "WASHING"( ) must be off.
Make sure that the "ON/OFF" ( )
button is pressed in.
To set the programme, press the "ON/OFF"
button: then turn the dial (in a clockwise or
anti-clockwise direction) until the pointer
( ) is in line with the symbol of the required
programme.
After about 4 seconds, the indicator light
"WASHING" will come on.
After an audible signal has sounded, the
programme will start automatically.
WITHIN 2 minutes of the programme
commencing another programme can be
selected, simply turning the programme
selector to the required position.
IMPORTANT
While a programme is running, the
programme selector will remain in
the selected position, and will NOT
MOVE.
Option button
"HALF LOAD" button
In response to your everyday washing
requirement in addition to the normal wash
functions this dishwasher is equipped with
the “HALF LOAD” function. This function
enables the uses to wash a reduced
number of dishes yet retaining the freedom
of loading them both on the top and bottom
basket. When this function is activated the
dishwasher will automatically reduce the
water and energy consumption and the
wash time. When selecting the “HALF
LOAD” ensure a reduced amount of
detergent is used.
The option button can be selected or
deselected WITHIN 2 minutes of the
programme commencing.
Interrupting a programme
Opening the door is not recommended
while a programme is running, especially
during the main washing phase and final
drying.
However, the dishwasher will stop automatically
when the door is opened.
If the door is opened during a programme,
the indicator light "WASHING" will start
flashing, up to when you re-close the door.
At this point, the programme will restart
from where it had been interrupted.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
If you wish to change or cancel the
programme that is running, carry out
the following:
turn the programme selector to "RESET"
position. After a few seconds the indicator
light "WASHING" will go off.
A new wash setting can now be made.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
"DELAY START" knob
"DELAY START" knob is used to postpone
the start of programmes by up to 12 hours.
This operation must be done before
pressing the "ON/OFF" button.
After setting the delayed start, the
"WASHING" indicator light will start to
flash, until at the end of countdown, will
stop flashing and remain on and the
programme will start automatically.
