Bedienungsanleitung Candy CH 642 (Seite 7 von 26) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

466229

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

SHUNT

7 GB-IE

Connection to the terminals on the terminal block

The hob is fitted with a power supply cord which allows it to be

connected only to a power supply of 220-240 V between phases

or between phase and neutral.

• Connect to a socket, to choose the correct fuse, you must

refer on the table.

It is however possible to connect the hob to :

. Three phase 220-240 V3~

. Three phase 380-415 V2N~

To proceed to the new connection, you must adhere the

following instructions.

• Before making the connection, make sure that the installation

is protected by a suitable fuse, see table, and that it is fitted with

wires of a large enough section to supply the appliance normally.

• Turn over the hob, glass side against the work top, taking care

to protect the glass.

• Open the cover in the following sequence:

1 2 3

• unscrew the cable clamp "1",

• find the two tabs located on the sides,

• put the blade of a flat screw-driver in front of each tab "2" e "3",

push in and press,

• remove the cover.

To release the power supplying cord.

• remove the screws retaining the terminal block which contains

the shunt bars and the conductors of the supply cord,

• Pull out the supply cord.

• Operations to be carried out to make a new connection :

- Choose the power supply cable in accordance with the

recommendations in the table.

- Pass the power supply cable into the clamp.

- Strip the end of each conductor of

the supply cord on a 10 mm length,

by taking in account the requested

length of the cord for the connection

to the terminal block.

- According to the installation

and with the help of shunt bars which

you should have recovered in the

first operation, fix the conductor as

shown on the chart.

- Fix the cover.

- Screw the cable clamp.

Note: make sure the terminal board screws are tight.

6. HOB COOKWARE ADVICE

• Always use good quality cookware with perfectly flat and

thick bases :

using this type of cookware will prevent hot spots that cause

food to stick. Thick metal pots and pans will provide an even

distribution of heat.

• Ensure that the base of the pot or pan is dry : when filling

pans with liquid or using one that has been stored in the

refrigerator, ensure that the base of the pan is completely dry

before placing it on the hob. This will help to avoid staining the hob.

• Use pans whose diameter is wide enough to completely

cover the surface unit : the size of the pan should be no

smaller than the heating area.

If it is slightly wider the energy will be used at its maximum

efficiency.

Using good quality cookware is critical for setting the best

performance from your hob.

5. PRESENTATION

• hilight zone :

a metallic conductor strip is spread uniformly over

the whole surface unit. It is effective within 3 seconds and is

suitable for steady, homogeneous and also sustained cooking.

The glass-ceramic hob benefits from greater heat output which

is generated by the hilight cooking zones thereby accelerating the

cooking process. Modifications to the design of the hob have not

affected the capacity of the glass to withstand high temperatures,

but they have improved controllability.

With the "Sprinter" facility, reduced cooking times of up to 15%

can be achieved, depending upon the method of cooking and the

type of saucepans being used.

LAY OUT

“ 5 ”

Fuse 25 A 25 A 25 A 20 A

Cable

HO5V2V2F

3x2,5 3x2,5 3x2,5 3x2,5

Fuse 25 A 20 A 25 A 20 A

Cable

HO5V2V2F

4x2,5 4x2,5 4x2,5 4x2,5

Fuse 16 A 20 A 20 A 16 A

Cable

HO5V2V2F

4x1,5 4x2,5 4x2,5 4x1,5

LAY OUT

“ 2 - 3 ”

LAY OUT

“ 4 ”

LAY OUT

“ 1 ”

ATTENTION:

should it be necessary to replace the supply cord, connect the

wire in accordance with the following colours/codes:

BLUE - NEUTRAL (N)

BROWN - LIVE (L)

YELLOW-GREEN - EARTH ( )

Ph = Phase N = Neutral T = Earth

Monophase 220-240 V~

Two phases 220-240 V2~

Three phases 220-240 V3~ Three phases 380-415 V2N~

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy CH 642 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info