Bedienungsanleitung Candy dfi 85 s (Seite 10 von 27) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

126428

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Selecting the programmes

and special functions

Use in conjunction with programme guide

Setting a programme

Open the door and press the button; the 5

programme selection indicator lights start flashing

to show that the machine is waiting for a selection

to be made.

Press the Programme Selection Button “P” and

the indicator light for the heavy wash program-

me will start flashing. Set the required programme

by pressing the Programme Selection Button

again. When then light for the required programme

starts flashing, close the door and when the

audible signal has sounded (if it has not been

deactivated) the programme will start

automatically.

Economy button E

The “E” button reduces the temperature of the

water during the last rinse. This activates a natural

drying process, as with a normal draining board,

simply by leaving the door ajar at the end of the

cycle to enable the natural circulation of air. The

“E” button provides an energy saving of more

than 20% and shortens the cycle.

Recommended for evening washes when the

dishes are not required perfectly dry, straight

away.

Interrupting a programme

It is not recommended that the door be opened

while a programme is running, and especially

not during the main wash phase and final

drying.

However, the appliance stops automatically

when the door is opened. At this point the “E”

button can be programmed or cancelled.

When the door is closed again, the programme

continues automatically. If you wish to change

or cancel a programme which is running, carry

out the following procedure:

open the door, keeping the Programme Selection

Button “P” pressed in until all 5 indicator lights

are flashing. A new setting can now be made.

NB: If, on pressing the Programme Selection

Button “P” the indicator lights start flashing

alternately, it means that there is water in the

machine.

Close the door to allow the water to be discharged

and wait for the audible signal, after which the

new programme can be set.

Before starting a new programme, you should

check that there is still detergent in the dispenser.

If necessary, top up the dispenser.

End of programme

The end of the programme is indicated by an

audible signal. When the door is opened the 5

programme selection indicator lights start flashing.

Release the button.

Activating and Deactivating the audible

signal

The audible signal function can be deactivated

in the following way:

keep the Programme Selection Button “P”

pressed in for a few seconds and at the same

time press the On/Off button; if the three indicator

lights “Intensive programme”, “Regular

programme” and “R 32’ Rapid programme”

are illuminated, the audible signal is activated.

By pressing the Programme Selection Button

“P” again, the “Normal programme” and “Eco

programme” lights will come on, which means

that the audible signal has been deactivated.

An audible signal sounds to indicate that the

setting has been stored in memory.

Attention

This dishwasher is equipped with an anti-overflow

safety device which works even when power is

switched off and and if the water level is too high

the supply will automatically be closed off.

Important

To ensure the correct operation of the anti-overflow

safety device, it is recommended not to move or

to tilt the dishwasher during operation.

If it is necessary to move or to tilt the dishwasher,

first make sure the washing cycle is finished and

that no water is left in the tank.

Regulating the water softener

with electronic programmer

The water softener can treat water with a hardness level of up to 90°fH (French

grading) or 50°dH (German grading) through 6 settings.

The settings, are listed in the panel below:

The softener unit is set in the factory at level 3 (Indicator light N.3) as this satisfies

the requirements of the majority of users. Regulate the setting of your water softener

unit according to the degree of hardness of your water as follows: open the door,

keep button “E” pressed in for a few seconds and at the same time press the On/Off

button .

The indicator light of button “E” will start flashing and indicator light N.3 (the factory

setting) will come on. To change the setting, press button “E”. Each time you press

that button, the next indicator light will come on. When the required indicator light

comes on, wait for the audible signal to confirm that the new setting has been stored

in memory.

Level

0-5

6-15

16-30

31-45

46-60

61-90

0-3

4-9

10-16

17-25

26-33

34-50

YES

Indicator light N.1

Indicator light N.2

Indicator light N.3

Indicator light N.4

Indicator light N.5

Water

hardness

°fH

(French)

Water

hardness

°dH

(German)

Use of

regenerating

salt

Water

softener

setting

N°1 N°2 N°3 N°4 N°5

BUTTON E

ON/OFF

BUTTON

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy dfi 85 s Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info