Bedienungsanleitung Candy EVO4 1072 (Seite 39 von 41) (Deutsch, Englisch, Portugiesisch, Spanisch)

513761

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

NOTE:

THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC DEVICE, WHICH PREVENTS THE SPIN CYCLE

SHOULD THE LOAD BE UNBALANCED.

THIS REDUCES THE NOISE AND VIBRATION IN THE MACHINE AND SO PROLONGS THE LIFE OF YOUR

MACHINE.

CHAPTER 13

FAULT

If the fault should persist, contact a Candy Technical Assistance Centre. For prompt

servicing, give the model of the washing machine, to be found on the label placed on

the cabinet inside of the porthole or on the guarantee certificate.

Important

1The use of environment friendly detersives without phosphates may produce the

following effects:

- The discharge rinse water may result cloudier due to the presence of zeolites in

suspension. This does not compromise the efficiency of the rinses.

- The presence of white powder (zeolites) on the washing at the end of the washing

cycle. This does not remain incorporated in the fabric and does not alter the colour.

- The presence of foam in the last rinse water which is not necessarily a sign of

inadequate rinsing.

- The non-ionic surface-active agents present in the composition of washing

machine detersives are often difficult to remove from the washing itself and, even in

small quantities, may produce visible signs of the formation of foam.

- Carrying out further rinses, in cases such as this, is not useful.

2If your washing machine fails to function, carry out the above-mentioned checks

before calling the Candy Technical Assistance Service.

1. Does not function

on any

programme

2. Does not load

water

3. Does not

discharge water

4. Water on floor

around washing

machine

5. Does not spin

6. Strong vibrations

during spin

7. Display reads error

0, 1, 5, 7, 8,9

8. Display reads

error 2

9. Display reads

error 3

10.Display reads

error 4

Mains plug not plugged in

Mains switch not on

No power

Electric circuit fuses failure

Load door open

See cause 1

Inlet tap turned off

Timer not set correctly

Discharge tube bent

Odd material blocking filter

Leak from the washer between the tap

and inlet tube

The washing machine has not

discharged water

“No spin” setting (some models only)

Washing machine not perfectly level

Transport bracket not removed

Washing load not evenly distributed

–

No water fill.

No pump out.

Machine overfilled with water.

Insert plug

Turn on mains switch

Check

Close load door

Check

Turn on water inlet tap

Set timer on correct position

Straighten discharge tube

Check filter

Replace washer and tighten the tube

on the tap

Wait a few minutes until the machine

discharges water

Turn the programme dial onto spin

setting

Adjust special feet

Remove transport bracket

Distribute the washing evenly

Call service.

Check water supplies are on.

Check drain is clear.

Check drain hose is not kinked.

Turn off water supply to machine.

Call service.

CAUSE

REMEDY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy EVO4 1072 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info