Bedienungsanleitung Candy FCO 105W (Seite 9 von 24) (Deutsch, Englisch)

495645

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

•Before making the connection, make sure that the installation is

protected by a suitable fuse, see table, and that it is fitted with

wires of a large enough section to supply the appliance normally.

•Turn over the hob, glass side against the work top, taking care to

protect the glass.

•Open the cover in the following sequence;

5.3 WIRING AND SAFETY OF THE BUILT-IN

COMBINED OVEN

Figure 17 Figure 18 Figure 19

• Unscrew the cable clamp “1”,

• Find the two tabs located on the sides,

• Put the blade of a flat screw-driver in front of each tab “2” e “3”,

push in and press,

• Remove the cover.

To release the power supplying cord.

• Remove the screws retaining the terminal block which contains

the shunt bars and the conductors of the supply cord,

• Pull out the supply cord.

•Operations to be carried out to make a mew connection:

-Choose the power supply cable in accordance with the

recommendations in the table.

-Pass the power supply cable in to the clamp.

-Strip the end of each conductor of the supply

cord on a 10 mm length, by taking in account

the requested length of the cord for the

connection to the terminal block.

-According to the installation and with the help

of shunt bars which you should have recovered

in the first operation, fix the conductor as

shown on the chart.

-Fix the cover.

-Screw the cable clamp.

Note: make sure the terminal board screws are

tight.

Shunt

Connection to the electrical circuit, on the oven or glass ceramic

hob, should be made via the oven. For this reason, it is important

that the instructions given in the oven instructions booklet are

followed carefully.

The ceramic hob without controls "PVS", has been developed to

be used only in conjunction with specific separate control units or

built in ovens with integral hob controls.

A detailed table (supplied with ovens with integral hob control or

with independent control units) shows clearly how the hobs are to

be connected to the specified units.

Under no circumstances must the hob be connected with any

other control or oven not specified in the list.

To proceed with the connection, it is necessary to joint male

connectors 1 and 2 of the hob with the “female”

connectors 3 of the oven or of the control panel.

5.4 VITROCERAMIC HOB WITHOUT

CONTROL KNOB “PVS”

550x10

22 mini

Bult-in oven "apertures" : Refer to the

instructon booklet concerned.

OVEN

HOB

INSTALLATION WITH OVEN

This connection can be made before or after the oven is

screwed into place.

Figure 22

L1: Phase

shunt 3-4 and

shunt 4-2

N: Neutral

shunt 1-5

T: Earth

L1: Phase

shunt 3-4 and

shunt 4-2

L2: Phase

shunt 1-5

T: Earth

L1: Phase

shunt 3-4

L2: Phase

shunt 2-5

L3: Phase

T: Earth

L1: Phase

L2: Phase

L3: Phase

N: Neutral

shunt 1-5

T: Earth

Figure 20

Figure 21

09 GB

MONOPHASE THREE-PHASE THREE-PHASE THREE-PHASE

VOLTAGE

FUSE

CABLE-SECTION

CABLE-TYPE

220 - 240 V2~ 380 - 415 V2~ 380 - 415 V3~ 380 - 415 V3N~

25 A 2 x 16 A

3 x 16 A

3 G 2.5 mm

4 G 1.5 mm

5 G 1.5 mm

HO5VV-F HO5VV-F HO5VV-F HO5VV-F

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy FCO 105W Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info