Bedienungsanleitung Candy PCV 64C (Seite 8 von 24) (Deutsch, Englisch)

495640

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENG

1.Place the hob into the opening on worktop. The size of opening

is given in Figure 11.

Fordetails, see the headings either Fixing the solid hotplate hob

or Fixing the vitroceramic hob.

.2.Connect the hob to the oven using the the plug given on the

hob. The socket for plug is placed on the rear panel of oven.

3.Connect the oven to the electrical supply.

4.Place the oven into its built-in niche. Either placement in Figure

11 is applicable depending on the size of cabinet opening. For

details, see the heading Fixing the oven.

5.2.1. Installation Steps

5.2.2. Fixing the solid hotplate hob

In order to prevent leakage of any liquids on the counter, a special

sealing putty is supplied together with your oven. Apply this putty

around the clearance on the kitchen counter. Extend the five-

piece putty by stretching and apply it around the clearance. Place

the hob on it, as indicated in the Figure 11. Make sure to fit all four

clamps by using one screw for each as shown in the Figure 12. In

case the thickness of the kitchen counter is less than 40mm, use

the clamp as shown in the Figure 14. After fitting your hob into its

place, neatly remove the excess sealing putty around the sides

with the help of a spatula Figure 13.

5.2.3. Fixing the vitroceramic hob

• Apply the one-sided self-adhesive sealing tape supplied

all the way round the lower edge of the cooking surface along the

outer edge of the glass ceramic panel. Do not stretch it.

• Screw the 4 worktop mounting brackets on the side walls

of product.

• Place the hob into the opening on the worktop.

Figure 13

h>40mm

h<40mm

Figure 12

Figure 14

Worktop mounting braket

5.2.4. Fixing the oven

Fit the oven into the space provided in the kitchen unit; it may be

fitted underneath a work top or into an upright cupboard. Fix the

oven in position by screwing into place, using the two fixing holes

in the frame. To locate the fixing holes, open the oven door and

look inside.

To allow adequate ventilation, the measurements and distances

indicated in the diagram on last page must be adhered to when

fixing the oven.

The dimensions and material of the cabinet in which the oven will

be installed must be correct and resistant to increases in

temparature. In a correct installation, contact with electrical or

insulated parts must be prevented. Insulating parts need to be

fitted in a way to ensure that they cannot be removed by using any

kind of tool. Installing the appliance in the close vicinity of a

refrigerator or a deep-freezer is not recommended. Otherwise, the

performance of the above-mentioned appliances will be

negatively affected due to emanating heat.

5.2.5. Warning

Warning regarding the installation of built-in oven without cooling

fan.

Prior inserting the oven, it is necessary to remove the rear kitchen

element panel in the area of the oven opening.

Equally, the front part of the element must have an opening.

Figure 15

Figure 16

60 cm

240 cm

120 cm

180 cm

08 GB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy PCV 64C Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info