Bedienungsanleitung Candy pvd 640 (Seite 11 von 37) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

335121

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

SHUNT

10 GB

550x10

22 mini

VITROCERAMIC HOB WITHOUT CONTROL

KNOBS "PVS"

This connection can be made before or after the oven is

screwed into place.

Built-in oven "apertures" : Refer to

the instruction booklet concerned.

Connection to the electrical circuit, on the oven or glass ceramic

hob, should be made via the oven. For this reason, it is important

that the instructions given in the oven instructions booklet are

followed carefully.

The ceramic hob without controls "PVS", has been developed to

be used only in conjunction with specific separate control units or

built in ovens with integral hob controls.

A detailed table (supplied with ovens with integral hob control or

with independent control units) shows clearly how the hobs are

to be connected to the specified units.

Under no circumstances must the hob be connected with any

other control or oven not specified in the list.

To proceed with the connection, it is necessary to joint male

connectors

1 and 2 of the hob with the "female" connectors

3 of the oven or of the control panel.

INSTALLATION WITH OVEN

OVEN

HOB

Connection to the terminals on the terminal block

• Models PVD

The hob is fitted with a power supply cord which allows it to be

connected only to a power supply of 220-240 V between phases

or between phase and neutral.

• Connect to a socket, to choose the correct fuse, you must

refer on the table.

It is however possible to connect the hob to :

. Three phase 220-240 V3~

. Three phase 380-415 V2N~

To proceed to the new connection, you must adhere the

following instructions.

• Before making the connection, make sure that the installation

is protected by a suitable fuse, see table, and that it is fitted with

wires of a large enough section to supply the appliance normally.

• Turn over the hob, glass side against the work top, taking care

to protect the glass.

• Open the cover in the following sequence:

1 2 3

• unscrew the cable clamp "1",

• find the two tabs located on the sides,

• put the blade of a flat screw-driver in front of each tab "2" e "3",

push in and press,

• remove the cover.

To release the power supplying cord.

• remove the screws retaining the terminal block which contains

the shunt bars and the conductors of the supply cord,

• Pull out the supply cord.

• Operations to be carried out to make a new connection :

- Choose the power supply cable in accordance with the

recommendations in the table.

- Pass the power supply cable into the clamp.

- Strip the end of each conductor of

the supply cord on a 10 mm length,

by taking in account the requested

length of the cord for the connection

to the terminal block.

- According to the installation

and with the help of shunt bars which

you should have recovered in the

first operation, fix the conductor as

shown on the chart.

- Fix the cover.

- Screw the cable clamp.

Note: make sure the terminal board screws are tight.

Ph = Phase N = Neutral T = Earth

Monophase 220-240 V~

Two phases 220-240 V2~

Three phases 220-240 V3~ Three phases 380-415 V2N~

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy pvd 640 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info