Bedienungsanleitung Candy PVD 642 X (Seite 10 von 37) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

74229

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer

safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in

accordance with the technical regulations in force. In the event that this advice is ignored and the installation is carried out

by an unqualified person, the manufacturer declines all responsibility for any technical failure of the product whether or not

it results in damage to goods or injury to individuals.

9 GB

BUILT-IN

The furniture in which your hob will be installed and all adjacent

furniture, should be made from materials that can withstand high

temperatures. In addition, all decorative laminates should be fixed

with heat-resistant glue.

Installation:

• A watertight seal is supplied with the hob.

Before fitting:

- turn the hob upside down, with the glass surface facing downwards.

Make sure the glass is protected.

- fit the seal round the hob.

- make sure that it is correctly fitted to avoid any leakage into the

supporting cabinet.

• Leave a gap of at least 5 cm between the appliance and the

vertical sides of the adjacent furniture.

• If, when installing the hob, the lower hob face is adjacent to an

area normally accessible when handling or cleaning, fit a partition

1 cm (7 cm for PVS) below the base of the hob to avoid any risk

of scorching or damage.

INSTALLATION

"The installation must conform to the standard directives."

The manufacturer declines all responsibility for any damage that

may be caused by unsuitable or unreasonable use.

Warning: we cannot be held responsible for any incident or

its consequences that may arise during the use of an appliance

not linked to the earth, or linked to an earth whose continuity

is defective.

• Always check before any electrical operation, the supply tension

shown on the electricity meter, the adjustment of the circuit-

breaker, the continuity of the connection to earth to the installation

and that the fuse is suitable.

• The electrical connection to the installation should be made via

a socket with a plug with earth, or via an omnipole cut-out switch

with an opening gap of at least 3 mm.

If the appliance has a socket outlet, it must be installed so that

the socket outlet is accessible.

ELECTRICAL CONNECTION

min 10 mm PVK -PVD

min 70 mm PVS

Sp da 25 a 45 mm

Accessible

space

Seal

Hob

min 70 cm

min 15 cm

min 5,5 cm

10 mm

mini

50 mm

Opening

500 X 50

Opening

500 X 10

It is forbidden

to fit the hob

above a non-

ventilated oven

3 G 2,5 mm2

H05RR-F,

H05VV-F,

H05V2V2-F

3 G 2,5 mm2

H05RR-F,

H05VV-F,

H05V2V2-F

4 G 2,5 mm2

H05RR-F,

H05VV-F,

H05V2V2-F

4 G 2,5 mm2

H05RR-F,

H05VV-F,

H05V2V2-F

5 G 1,5 mm2

H05RR-F,

H05VV-F,

H05V2V2-F

Monophase

220-240V~

Two phases

220-240V2~

Two phases

220-415V2N~

Three phases

220-240V3~

Three phases

380-415V3N~

20 A 20 A 20 A 20 A 16 AFUSE

CABLE

AREA

TYPE

PH Phase

shunt 1-2

shunt 2-3

N Neutral

shunt 4-5

T Earth E

CONNEC-

TION TO

THE

TERMIMAL

BLOCK

PH N T PH PH T PH N TPH PHPH PH T TPHPH PH N

PH Phase

shun 1-2

shunt 2-3

PH Phase

shunt 4-5

T Earth E

PH Phase

shunt 2-3

N Neutral

shunt 4-5

T Earth E

PH Phase

shunt 1-2

PH Phase

shunt 3-4

PH Phase

T Earth E

PH Phase

N Neutral

shunt 4-5

T Earth E

• PVK Models

A power cord is not supplied with the appliance, but the hob is

equipped with a terminal block which enables you to choose the

correct connection for the particular power supply.

CONNECTION TO THE TERMINALS ON THE TERMINAL BLOCK:

ELECTRICAL CONNECTION

• The yellow/green wire of the power supply cable must be

connected to the earth of both power supply and appliance

terminals.

• Any queries regarding the power supply cord should be referred

to After Sales Service or a qualified technician.

Terminal block

with marks

Shunts

bars

Earth

Terminal

Cord clamp

To proceed with the connection, you must adhere to the following

instructions.

• Before making the connection, make sure that the installation

is protected by a suitable fuse, see table, and that it is fitted

with wires of a large enough section to supply the appliance

normally.

• Choose the supply cord in accordance with the recommendations

in the table.

• Turn the hob, with the glass side against the worktop, providing

you have protected the glass !

• Remove the cover located under the control

knobs, fitted by 2 screws at the front.

• Pass the supply cord into the cover hole.

• Pass the supply cord into the clamp.

• Strip the end of each conductor of the supply

cord on a 10 mm length, by taking account of the requested

length of the cord for the connection on the terminal block.

• The terminal block offers different types

of connection.

So, in accordance with installation

instructions and with the help of shunt

bars*, fix the conductors as shown on

the chart.

* The shunt bars, placed on the Earth

Terminal,

allow to make a bridge between two

phases. Screw the screw fully home.

Note : Please take care to ensure

that the shunt bars do not fall through

the hole.

• Screw the cable clamp back.

• Screw the cover hole back do not forget

the fan-lock washers.

Candy PVD 642 X Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info