Bedienungsanleitung Candy TRIO 9503 (Seite 5 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

511273

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ELECTRICAL CONNECTION

"The installation must conform to the standard directives".

The manufacturer declines all responsibility for any damage that

may be caused by unsuitable or unreasonable use.

Warning :

• Always check before any electrical operation, the supply tension

shown on the electricity meter, the adjustment of the circuit-

breaker, the continuity of the connection to earth to the installation

and that the fuse is suitable.

• The electrical connection to the installation should be made via

a socket with a plug with earth, or via an omni pole cut-out

switch .

If the appliance has a socket outlet, it must be installed so that

the socket outlet is accessible.

The manufacturer cannot be held responsible for any accidents

resulting from the use of an appliance which is not connected

to earth, or with a faulty earth connection continuity.

• Any queries regarding the power supply cord should be referred

to After Sales Service or a qualified technician.

Warning! This appliance must be earthed. In the absence of

adequate earthing you will notice that when touching the

metal parts of your appliance an electrical dispersion can be

felt due to the presence of a radio interference suppressor.

• TRIO 9501

A power cord is supplied with the Trio which allows it to be

connected only to a power supply of 220-230 V between

phases, or between phase and neutral. Connect to a 10/16

Amp socket.

• TRIO 9503

A power cord is not supplied with this Trio, but it is equipped with

a terminal block that enables you to choose the correct connection

for the particular power supply.

The terminal block is located at the back of the Trio.

To open the terminal block :

. Locate the two tabs on the sides,

. place the screwdriver blade on the front of the tab, insert it (1)

and press down (2)

. Lift the cover off.

Terminal block

x 3 bars shunts

To connect :

. unscrew the cable grip,

. pass the cable through the cable grip,

. strip the insulation off the end of the each wire and connect them

to the according to the numbers shown in the table as well as

the "bars shunts".

4 GB

INSTALLATION

Example of connection in monophase

1- Put in the

bars shunts

2- Put in

the wires

3- Pass the cable

through the cable grip

Caution: incorrect tightening can cause dangerous heating

risks for the power supply cable.

H05VV-F

3 G 2,5 mm

Monophase

220-230V~

25 AFUSE

CABLE

TYPE-AERA

2 Phase

Shunt 1-2

Shunt 2-3

5 Neutral

Shunt 4-5

T Earth

CONNEC-

TION TO

THE

TERMINAL

BLOCK

To Shunt:

make a

bridge with a

shunt bar

H05RR-F,

H05VV-F or,

4 G 2,5 mm

H05VV-F or,

H05RR-F

5 G 1,5 mm

Three phases

220-230V3~

Three phases

380-415V3N~

25 A 16 A

1 Phase

Shunt 1-2

3 Phase

Shunt 3-4

5 Phase

T Earth

1 Phase

2 Phase

3 Phase

5 Neutral

Shunt 4-5

T Earth

When the connection operation to the appliance terminals is

finished, tighten the cable clamp and close the cover.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Candy TRIO 9503 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info