Bedienungsanleitung Canon EOS C500PL (Seite 80 von 212) (Englisch)

543073

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

Adjusting the Focus

NOTES

• If the focus mode switch on the EF lens is set to MF, you will not be able control the focus through remote

operation. Depending on the lens used, remote operation may not work correctly.

• If you operate the zoom after focusing, the focus on the subject may be lost.

• If you focus manually and then leave the camera with the power turned on, the focus on the subject may be

lost after a while. This possible slight shift in focus is a result of the internal temperature rising in the camera

and lens. Check the focus before resuming shooting.

• While the camera is focusing, do not touch the end of the lens or focus ring while they are moving.

Using the Focus Assistance Functions

In order to focus more accurately, you can use two focus assistance functions – peaking, which creates a clearer

contrast by emphasizing the outlines of the subject, and magnification, which enlarges the image on the screen.

You can use both functions simultaneously for greater effect.

You can also use the [w Other Functions] > [Custom Function] > [F. Assist. B&W] setting (A 122) to switch

the screen and output from the MON. terminals to black & white while using the focus assistance functions.

Peaking

The camera offers two peaking levels to help you focus more accurately.

1 Press the PEAKING button.

• The peaking icon (J or K) appears at the lower center of the

screen and the outlines in the image on the screen will be

emphasized, depending on the focus.

• Press the button again to turn off peaking.

• Alternatively, you can use the [£ LCD/VF Setup] > [Peaking]

setting to turn peaking on and off.

2 Open the [Select] submenu (under [Peaking]) to select the peaking level.

[£ LCD/VF Setup] > [Select] (under [Peaking])

3 Select the desired level and then press SET.

• You can use the [£ LCD/VF Setup] > [Peaking 1] and [Peaking 2]

> [Color], [Gain] and [Frequency] settings to set the color, gain and

frequency of the two peaking levels independently of each other.

However, only [Color] will be applied to an external monitor

connected to the MON. 1 terminal. Perform the following procedure

to adjust the peaking gain on an external monitor.

To adjust the peaking gain on an external monitor

1 Open the [Peaking Gain] submenu.

[ 4K/2K/MXF Setup] > [MON. 1] > [Peaking Gain]

2 Push the joystick up/down or turn the SELECT dial to set the level and

then press SET.

Magnification

1 Press the MAGN. button.

• ^ appears at the lower center of the screen and the center of the

picture is magnified approximately 2 times*.

• A white frame representing the whole screen area is displayed on the top left of the screen. The orange

frame within it represents the approximate part of the image shown magnified.

[£ LCD/VF Setup]

[Select]

(under [Peaking])

[Peaking 1]

[ 4K/2K/MXF Setup]

[MON. 1]

[Peaking Gain]

[10]

COPY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon EOS C500PL Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon EOS C500PL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info