Bedienungsanleitung Canon EOS C700 FF PL (Seite 31 von 255) (Englisch)

683260

Zoom out

Zoom in

Vorherige Seite

1/255

Nächste Seite

Changing Camera Settings with the Screen Buttons

Following is a step-by-step example of how to change a setting using the screen buttons. In the manual, these

will be abbreviated in most cases. For example, the instruction below stands for the procedure following it.

[SHUTTER] > Desired shutter value > Press SET

1 Press the HOME button.

• The HOME screen will appear.

2 Press the [SHUTTER] screen button.

• The shutter speed selection screen will appear with the current shutter

speed value marked with an orange selection frame.

3 Turn the SELECT dial to select the desired value and then press

SET.

• The selected value will be applied and the previous screen will be

displayed. If necessary, press the HOME button to return to the

HOME screen.

• You can press the BACK button instead of the SET button to return

to the previous screen without changing the current value.

Adjusting the Control Display

You can adjust the brightness of the control display on the camera or on an optional OU-700 Remote Operation

Unit connected to the camera. This adjustment will not affect your recordings.

1 Open the control display's [Brightness] submenu.

[Monitoring Setup] (

) > [Control Display] > [Camera] or [Remote OU-700] > [Brightness]

2 Select the desired level ([5] is the brightest) and then press SET.

• Alternatively, you can adjust the control display’s brightness from the HOME screen by turning the SELECT

dial while holding the BACK button pressed down.

NOTES

• If necessary, you can remove the control display’s protective cover inserting a fingernail or other thin object

under the bottom center of the cover and pulling it. After cleaning the control display place back the protective

cover on the control display and push all four corners to secure it in place.

• With the [Monitoring Setup] > [Control Display] > [Camera] > [Turn Off Display] setting, you can

set the camera so the camera’s control display is turned off automatically whenever an optional OU-700

Remote Operation Unit is connected to the camera.

• If you set an assignable button to [Control Display Setup] (A 127), you can press the button to open the

monitoring menu’s [Control Display] submenu. If you set an assignable button to [Control Display] (A 127),

you can press the button to turn the control display on/off.

• You can use the [System Setup] > [LED] > [Button Illumination] setting to turn on the buttons’

illumination and change their brightness. Alternatively, you can do so from the HOME screen by turning the

SELECT dial while holding the HOME button pressed down.

• About the control display and optional viewfinder: The screens are produced using extremely high-precision

manufacturing techniques, with more than 99.99% of the pixels operating to specification. Very rarely, pixels

may misfire or may light up permanently as white dots. This has no effect on the recorded image and does not

constitute a malfunction.

햳

햴

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon EOS C700 FF PL Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon EOS C700 FF PL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info