Bedienungsanleitung Canon EOS R5 C (Seite 102 von 254) (Englisch)

809437

102

Zoom out

Zoom in

Vorherige Seite

1/254

Nächste Seite

Setting the Time Code

102

Selecting Drop or Non-Drop Frame

When the frame rate is set to 59.94P, 59.94i or 29.97P, you can select between a drop frame (DF) or non-drop

frame (NDF) time code, depending on how you plan to use your recordings.

With all other frame rates, the time code is set to non-drop frame (NDF) and cannot be changed.

Select > [

System Setup] > [Time Code DF/NDF] > Desired option.

• The time code display will change depending on the setting. When you select [DF], the time code will appear

as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].

About the time code display

A letter may appear next to the time code depending on the setting/status. Refer to the following table.

NOTES

• The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P or 24.00P), from 0 to 24 (frame

rate set to 25.00P, 50.00i or 50.00P), or from 0 to 29 (all other frame rates).

• When slow & fast motion recording/frame recording/interval recording is activated, you cannot select the [Free

Run] running mode. Conversely, when pre-recording is activated, [Free Run] is set automatically and cannot be

changed.

• When slow & fast motion recording/frame recording/interval recording is activated, the time code signal will not

be output from any of the terminals.

• When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at

the point where the recording starts.

• When you are using the [Free Run] running mode, the time code will continue running as long as the built-in

backup battery has some charge left, even if you disconnect all other power sources.

• If you set an assignable button to [Time Code] (A125), you can press the button to open the

[B System Setup] menu page with the time code settings.

Setting the User Bit

You can set a user bit composed of the date or the time of recording or an identification code consisting of

8 characters in the hexadecimal system. There are sixteen possible characters: the numbers 0 to 9 and the

letters A to F.

The user bit is recorded with clips and can be output from the TIME CODE terminal/HDMI OUT terminal. It can

be used freely to categorize and manage recordings or to keep additional information about them.

1Select > [

System Setup] > [User Bit Type] > [Setting], [Date] or [Time].

• If you select [Time] or [Date] the rest of the procedure is not necessary.

2Select [Change].

• To reset the user bit to [00 00 00 00], select [Reset] instead.

3 Enter the user bit using the data entry screen (A25).

Letter Description

RThe time code mode is set to [Regen.].

PThe time code mode is set to [Preset] and the running mode is set to [Rec Run].

FThe time code mode is set to [Preset] and the running mode is set to [Free Run].

EThe time code signal is coming from an external source.

No letter Time code during clip playback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon EOS R5 C Seite 102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon EOS R5 C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info