Bedienungsanleitung Canon HV10 (Seite 63 von 89) (Englisch)

55775

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

Connecting to a Computer

External Connections

Transferring Video Recordings

You can transfer recordings to a computer

using the HDV/DV terminal.

Equipment and System Requirements

A computer equipped with an

IEEE1394 (DV) terminal or an IEEE1394

(DV) capturing board.

A DV cable (Use the optional CV-150F

(4 pin-4 pin) or CV-250F (4 pin-6 pin) DV

Cable).

Video Editing Software.

The appropriate driver

The standard of the video transferred

depends on the standard of the original

recording and the compatibility of the

video editing software.

When transferring a video originally

recorded in HDV standard, if the editing

software supports high definition video,

the video transferred will be in HDV

standard too. If the editing software does

not support high definition video, even if

the original recording was made in HDV

standard, the video transferred will be in

DV standard.

POINTS TO CHECK

Change the following settings as necessary

before making the connections. Refer to the

corresponding explanation of each setting in the

PLAY/OUT SETUP

menu option list

(32).

- [PLAYBACK STD] and [DV OUTPUT] to

select the standard of the output video. Note

that the video standard of the transferred video

depends also on the standards supported by

the editing software.

- [AV DV] to select whether to transfer

recordings from the tape in the camcorder (set

to [ OFF]) or video converted from an

external analog source (set to [ ON]).

Connecting

1 Start the computer.

2 Set the camcorder to

mode.

3 Connect the camcorder to the

computer using the digital

connection –connection type

( 62)– shown in the previous

section

PC Connection Diagrams

When the connection is recognized

“ HDV/DV” will be displayed. When

the video output starts the display will

change to “ HDV-OUT” or “ DV-

OUT” depending on the original

recording and the settings selected.

4 Start the video editing software.

Refer to the instruction manual of the

editing software.

IMPORTANT

The video transfer may not work correctly

depending on the software and the

specifications/settings of your computer.

If the computer freezes while the camcorder

is connected to it, disconnect the DV cable and

turn off the camcorder and the computer. After a

short while, turn them on again, set the

camcorder to mode and restore the

connection.

Before connecting the camcorder to the

computer using a DV cable, make sure that the

camcorder and computer are not connected

with a USB cable, and that no other IEEE1394

device is connected to the computer.

Depending on the video editing software, you

may need to set the POWER switch of the

camcorder to a mode other than PLAY. Refer to

the instruction manual of the editing software.

NOTES

We recommend powering the camcorder

using the compact power adapter.

Refer also to the instruction manual of the

computer.

The programs ZoomBrowser EX and Image

Browser included with the supplied CD-ROM

can only be used to transfer still images

recorded on the memory card. Video recordings

on the tape cannot be transferred to the

computer using the software included with the

supplied CD-ROM.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon HV10 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon HV10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info