When the logic board ass'y is replaced, reset the waste ink counter. In addition, according to the waste ink amount, replace the waste ink absorber (the bottom case
unit or the ink absorbers). The standard amount for waste ink absorber replacement is given in the table below.
*1: Check the waste ink amount by service test print or EEPROM information print.
[See 3.3. Adjustment / Settings, (6) Service mode, for details.]
(5) User mode
<Standalone printer operation>
1) Turn on the printer.
2) Press and hold the Resume/Cancel button until the LED blinks the specified number of times listed in the table below, and release it. The operation starts.
Waste ink amount
*1
Bottom case unit or ink absorber replacement
Less than 7%Not required.
7% or moreRequired.
FunctionProceduresRemarks
Print head manual cleaning- Cleaning both black and color:
See "Standalone printer operation" below.
- Cleaning black or color separately, or both black and color:
Perform from the printer driver's Maintenance tab.
Print head deep cleaning- Cleaning black or color separately, or both black and color:
Perform from the printer driver's Maintenance tab.
Paper feed roller cleaningSee "Standalone printer operation" below.
Nozzle check pattern printing
See "Standalone printer operation" below.
Also available from the printer driver's
Maintenance tab.
Print head alignmentSee "Standalone printer operation" below.In Custom Settings of the printer driver's
Maintenance tab, manual print head alignment (by
selecting the optimum values) as with the
conventional models can be performed.
Bottom plate cleaningPerform from the printer driver's Maintenance tab.Cleaning of the platen ribs when the back
side of paper gets smeared.
Print head replacementThe print head is replaceable at the same position as for
ink tank replacement. (Open the access cover. When the
carriage stops at the center, the print head can be
replaced.)
LED blinkingOperationRemarks
1 timePrint head manual cleaning
2 timesNozzle check pattern printingSet a sheet of plain paper (A4 or letter) in the ASF or the cassette (according
to the Paper Feed switch setting).
3 timesPaper feed roller cleaning
4 timesAutomatic print head alignmentSet a sheet of plain paper (A4 or letter) in the ASF.
5 timesBottom plate cleaningFold a sheet of plain paper (A4 or letter) in half crosswise, then unfold and set
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Canon iP4000 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.