214647
70
Zoom out
Zoom in
Vorherige Seite
1/83
Nächste Seite
6
7. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
WARNING Indicator
LAMP Indicator
Indicator Messages
POWER Indicator
MENU
BACK
KEYSTONE
WARNING
P
O
W
E
R
AUTO PC
INPUT
VOL
-
VOL
+
LAMP



Indicator Condition Projector Condition Note
Off
The main power is off
Blinking light Green 0.5 sec On,
0.5 sec Off
The projector is getting ready
to turn on.
Wait for a moment.
2.5 sec On,
0.5 sec Off
Off Timer is enabled.
Orange 0.5 sec On,
0.5 sec Off
T he p ro j e c t or i s c oo l in g
down.
Wait for a moment.
Steady light Green The projector is turned on.
Orange The projector is in Standby.
Indicator Condition Projector Condition Note
Off Normal
Blinking light Red 1 c yc le ( 0 .5 se c
On, 2.5 sec Off)
L a mp cover err o r or lamp
housing error
Replace the lamp cover or lamp housing correctly.
(
page 60)
2 c yc le ( 0 .5 se c
On, 0.5 sec Off)
Temperature error The projector is overheated. Move the projector to a
cooler location.
4 c yc le ( 0 .5 se c
On, 0.5 sec Off)
Fan error Fans will not work correctly.
6 c yc le ( 0 .5 se c
On, 0.5 sec Off)
Lamp error Lamp fails to light. Wait a full minute and then turn on
again.
Green Re-firing the lamp (The pro-
jector is cooling down.)
The projector is re-firing.
Wait for a moment.
Steady light Orange Key lock is on. You have pressed cabinet button when Key lock is on.
(
page 50)
Indicator Condition Projector Condition Note
Off Normal
Blinking light Red Lamp has reached its end of life. Lamp
replacement message will be displayed.
Replace the lamp.
Steady light Red Lamp has been used beyond its limit.
The projector will not turn on until the
lamp is replaced.
Replace the lamp.
Green Lamp mode is set to Quiet mode.
If a temperature error occurs
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the
WARNING indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
- Unplug the power cord after the cooling fans stop.
- Move the projector to a cooler location if the room where you are presenting is particularly too warm.
- Clean the ventilation holes if they are clogged with dust.
- Wait about 60 minutes until the inside of the projector becomes cool enough.
70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Canon lv 7260 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info