Bedienungsanleitung Canon lv 7275 (Seite 70 von 94) (Englisch)

216212

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

6

. Usng On-Screen Menu

Selectng Communcaton Speed [Communcaton speed]

This feature sets the baud rate of the SERVICE PORT (D-Sub 9 Pin). It supports data rates from 4800 to 19200

bps.

The default is 19200 bps.

Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud

rate may be recommended for long cable runs).

NOTE: Your selected communication speed will not be affected even when [Reset] is done from the menu.

[Options (1)]

Settng Auto Adjust [Auto PC adjustment]

Selecting [Normal] or [Fine] will automatically execute Auto PC adjustment function at the time of signal switching.

This feature sets the Auto PC adjust mode so that the analog RGB image can be automatically or manually adjust-

ed for noise and stability. You can automatically make adjustment in two ways: Normal and Fine

Off .......................... The RGB image will not be automatically adjusted.

You can manually optimize the RGB image.

Normal ................... Default setting. The RGB image will be automatically adjusted. Normally select this option.

Fine ........................ Select this option if ﬁne adjustment is needed. It takes more time to switch to the source than when [Nor-

mal] is selected.

Enablng Fan Speed Mode [Fan mode]

This option allows you to select two modes for fan speed: Auto, High, and High altitude.

Auto .......................................... The built-in fans automatically run at a variable speed according to the internal temperature.

High .......................................... The built-in fans run at a ﬁxed high speed.

High altitude ............................. The built-in fans run at a high speed. Select this option when using the projector in places at

5500 ft./1600 m or higher.

When you wish to cool down the temperature inside the projector quickly, select [High].

NOTE: It is recommended that you select High speed mode if you continue to use the projector for consecutive days.

NOTE:

• It is recommended that you select High speed mode if you use the projector non-stop for consecutive days.

• Be sure to select [High altitude] when using the projector at altitudes approximately 5500 feet/1600 meters or higher.

• Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [High altitude] can cause

the projector to overheat and the protector could shut down. Furthermore, the projector could not turn on due to the in-

creased temperature of the lamp after power off. If these happen, wait a couple minutes and turn on the projector.

• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [High altitude] can cause the

lamp to overcool, causing the image to ﬂicker.

• Your Fan mode setting will not be affected even when [Reset] is done from the menu.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon lv 7275 Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info