Bedienungsanleitung Canon LV-WX370 (Seite 100 von 116) (Englisch)

709658

100

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

100

Maintenance and cleaning

Follow steps below to replace the lamp:

1. Power off your projector and unplug the AC pow-

er cord. Let it cool down for at least 1 hour.

2. Open the lamp cover after removing screws

holding the cover.

 

lamp by holding its handle.

4. Replace with a new lamp and tighten all 3

screws. Make sure the lamp has been installed

correctly. Close the lamp cover and tighten the

screw.

5. Connect your projector to an AC power source

and power it on.

Precautions when replacing lamps that stop working

If the illumination suddenly stops when the projector is in use or after you turn it

on, the lamp may be broken. In this case, never attempt to replace the lamp by

yourself. Always request service from a qualified technician or the Canon Cus-

tomer Support Center. Additionally, with ceiling-mounted projectors, the lamp

may fall out when you open the lamp cover or while you are attempting to re-

place it. During replacement, make sure no one is under the projector, and stand

to the side of the lamp cover, not directly under it.

Note:

Let your projector cool for at least 1 hour before opening the lamp cover, as

temperature within your projector is high.

Note:

Replace the lamp with a new one of the same model only when it is necessary.

Do not drop or touch the lamp! It may break and lead to personal injuries.

Lamp cover

Screw

Precautions on lamp operation

Your projector employs high voltage lamp, which requires careful and correct operation.

Fail to do so may lead to accidents, personal injuries, or fire.

 Useful life of lamps varies widely from lamp to lamp and depending on the environment

of use. Some lamps may fail or rupture soon after they are first used.

 If your projector prompts you to replace lamp (by showing a lamp replacing icon) then

replace it with a new one after powering it off and it is fully cooled down. (Please re-

place lamp by strictly following steps given in this manual.)

If you keep on using the lamp after being prompted to replace it then you are exposed

to greater risks of lamp explosion.

 Lamp may explode due to external impact and shock. Risks of explosion vary with

projector and use environment and status of the lamp.

In case of lamp explosion, take the following safety measures:

Disconnect your projector from power source immediately in case of lamp explosion. Call

authorized service center to inspect your projector and replace lamp. Make a thorough

inspection to ensure every piece of debris after explosion has been removed. Remove ev-

ery piece of debris after explosion. No one else may inspect the internal of your projector

except those authorized and well trained technician who also are familiar with its mainte-

nance. Or we shall not be held liable for the consequences.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon LV-WX370 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon LV-WX370

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info