Bedienungsanleitung Canon LV-X300 (Seite 30 von 77) (Englisch)

615751

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up

password security. The password can be set through the On-Screen Display (OSD) menu. For details of

the OSD menu operation, please refer to "Using the menus" on page 29.

You will be inconvenienced if you activate the power-on lock functionality and subsequently forget

the password. Print out this manual (if necessary) and write the password you used in this manual,

and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set, the projector cannot be used unless the correct password is

entered every time the projector is started.

1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings menu. Press

OK/IMAGE. The Security Settings page is displayed.

2. Highlight Power On Lock and select On by pressing / .

3. As pictured to the right, the four arrow keys ( , , , )

respectively represent 4 digits (1, 2, 3, 4). According to the password

you desire to set, press the arrow keys to enter six digits for the

password.

4. Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the Security

Settings page.

The digits being input will be displayed as asterisks on-screen. Write your selected password down

here in this manual in advance or right after the password is entered so that it is available to you

should you ever forget it.

Password: __ __ __ __ __ __

Keep this number in a safe place.

5. To leave the OSD menu, press MENU.

If you forget the password

If the password function is activated, you will be asked to enter the six-

digit password every time you turn on the projector. If you enter the wrong

password, the password error message as pictured to the right is displayed

lasting for three seconds, and the message 'INPUT PASSWORD' follows.

You can retry by entering another six-digit password, or if you did not

record the password in this manual, and you absolutely do not remember it,

you can reset the password function. See "Resetting the password

function" on page 30 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a

short time.

Resetting the password function

1. Turn the projector off. See "Shutting down the projector" on page 42 for details.

2. Unplug the power cord.

3. Long press MENU and Right on the projector until the power cord was plugged.

4. Now the password function has been reset and the Power On Lock is Off. You can turn on the

projector without entering any password. You can also activate the power-on lock functionality as if

you were setting the password for the first time. See "Setting a password" on page 30 for details.

Changing the password

1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings > Change

Password menu.

2. Press OK/IMAGE. The message 'INPUT CURRENT PASSWORD' is displayed.

Input New Password

Back

Password Error

Please try again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon LV-X300 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon LV-X300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info