Bedienungsanleitung Canon lv x6 (Seite 66 von 77) (Englisch)

214543

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

7. Appendix

Common Problems & Solutions (See also "POWER/WARNING/LAMP Indicator" on page 56.)

Does not turn on

Will turn off

No picture

Picture suddenly

becomes dark

Color tone or Color

balance is unusual

Image isn’t square to

the screen

Picture is blurred

Image is scrolling

vertically, horizontally

or both

Remote control does

not work

Indicator is lit or

blinking

Cross color in RGB

mode

Whenever the projector

is turned on, a message

prompting you to clean

the filter will be dis-

played

• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote

control is on. See pages 19 and 20.

• Ensure that the lamp cover is installed correctly. See page 55.

• Check to see if the projector has overheated or the lamp usage exceeds 2100* hours (up to 3100* hours :

Quiet mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is

particularly warm, move the projector to a cooler location.

*LV-X6: 3100 hours (up to 4100 hours in Quiet mode).

• The lamp may fail to light. Wait a full minute and then turn on the power again.

• The lamp has reached the end of its usable life. Replace the lamp.

• Ensure that the Power Management or Off timer is off. See page 47.

• Use the INPUT button to select your source (LV-7250: Computer 1, Computer 2, Video or S-Video / LV-X6:

Computer, Video or S-Video). See page 22. If there is still no picture, press the button again.

• Ensure your cables are connected properly.

• Use menus to adjust the brightness and contrast. See page 42.

• Remove the lens cap.

•

Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. See page 50.

• Enter your registered Password if the Password function is enabled. See page 33.

• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning

on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook

PC is turned on after connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-

saver or power management software.

• See also the next page.

• When the room where you' re presenting is particularly warm → Move the projector to a cooler location.

• Check if an appropriate color is selected in [Screen color]. If so, select an appropriate option. See page 44.

• Adjust [Color balance] in [Image adjustment]. See page 42.

• Reposition the projector to improve its angle to the screen. See page 23.

• Use the Keystone correction function to correct the trapezoid distortion. See page 25.

• Adjust the focus. See page 24.

• Reposition the projector to improve its angle to the screen. See page 23.

• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page

12.

• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

• Use the INPUT button to select your source (LV-7250: Computer 1, Computer 2, Video or S-Video / LV-X6:

Computer, Video or S-Video). See page 22.

• Adjust the computer image manually with the [Horizontal position] or [Vertical position] in the [Display set-

tings]. See page 43.

• Install new batteries.See page 10.

• Make sure there are no obstacles between you and the projector.

• Stand within 7 m (22 feet) of the projector. See page 10.

• See the POWER/WARNING/LAMP Indicator on page 56.

• Press the AUTO PC button on the projector cabinet or the remote control. See page 27.

• Adjust the computer image manually with [Clock] or [Tracking] in [Display settings] in the menu. See page 43.

• Clean or replace the filter and then reset the Filter counter. See page 51.

Problem Check These Items

For more information contact your dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon lv x6 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info