Bedienungsanleitung Canon LX-MW500 (Seite 68 von 85) (Englisch)

709680

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

Replacing the lamp Spare lamp: LX-LP02

• Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector.

Contact your dealer for purchase of the lamp.

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power

cord before changing the lamp.

• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before

replacing the lamp.

• To reduce the risk of compromising image quality, do not touch the optical components inside

when the lamp is removed.

• Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate.

Improper installation may also result in fire.

• If the lamp should break, never shake the lamp box or hold it in front of your face after

removing it. The glass fragments may fall out and cause injury to your eyes.

• In the event that the high-pressure mercury lamp exploded, glass fragments may have been

scattered inside the projector. Ask your dealer to replace the lamp and to inspect the inside of

the projector. When you clean or replace the lamp by yourself, be sure to hold the handle of the

lamp. You may get injured by glass fragments.

• Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling.

• Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the

lamp may result in a breakdown.

• This projector uses a high-pressure mercury lamp as the light source. The high-pressure

mercury lamp may explode or fail to illuminate permanently because of an impact, scratch, or

deterioration through use. The period of time until explosion or permanent failure to illuminate

varies considerably from lamp to lamp, depending on operation conditions. Therefore, the

lamp may explode soon after the start of use.

• The possibility of explosion of the lamp increases if you use it beyond its replacement period.

When the instruction of lamp replacement appears, replace it with a new one immediately even

if the lamp is still lighting normally.

• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside

the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector.

The gas inside the lamp contains mercury. Be careful not to breathe it or avoid it from entering

your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor

immediately.

• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this

lamp in a proper manner.

• Be sure to use the lamp dedicated to this projector, LX-LP02. Use of other lamps may cause a

failure of the projector.

1. Turn the power off and disconnect the projector from the

wall socket. If the lamp is hot, avoid burns by waiting for

approximately 45 minutes until the lamp has cooled.

2. Unscrew the screws on the lamp cover.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon LX-MW500 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon LX-MW500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info