Bedienungsanleitung Canon MF4450 Image Class (Seite 21 von 164) (Englisch)

467374

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

C. Power Requirements

The machine should be connected to a standard 120 volt

AC, three-wire grounded outlet only.

Do not connect this machine to an outlet or power line

shared with other appliances that cause “electrical noise.” Air

conditioners, electric typewriters, copiers, and machines of

this sort generate electrical noise that often interferes with

communications equipment and the sending and receiving

of documents.

Connection of the Equipment

This equipment complies with Part 68 of the FCC rules and the

requirements adopted by the ACTA. On the rear panel of this

equipment is a label that contains, among other information,

a product identifier in the format of US:AAAEQ##TXXXX. If

requested, this number must be provided to the telephone

company.

The REN (Ringer Equivalence Number) is used to determine the

number of devices that may be connected to a telephone line.

Excessive RENs on a telephone line may result in the devices

not ringing in response to an incoming call. In most, but not all

areas, the sum of the RENs should not exceed five (5.0).

To be certain of the number of devices that may be connected

to a line, as determined by the total RENs, contact the local

telephone company. The REN for this product is part of the

product identifier that has the format US: AAAEQ##TXXXX. The

digits represented by ## are the REN without a decimal point

(e.g., 10 is a REN of 1.0).

An FCC compliant telephone line cable and modular plug is

provided with this equipment. This equipment is designed

to be connected to the telephone network or premise wiring

using a compatible modular jack that is Part 68 compliant.

This equipment may not be used on coin service provided by

the telephone company. Connection to party lines is subjected

to state tariffs.

In Case of Equipment Malfunction

Should any malfunction occur which cannot be corrected

by the procedures described in this guide or the e-Manual,

disconnect the equipment from the telephone line cable and

disconnect the power cord.

The telephone line cable should not be reconnected or the

power switch turned ON until the problem is completely

resolved. Users should contact Canon Authorized Service

Facilities for servicing of equipment, Information regarding

Authorized Service Facility locations can be obtained by calling

Canon Customer Care Center (1-800-OK-CANON).

Rights of the Telephone Company

If this equipment (imageCLASS MF4570dn/MF4450) causes

harm to the telephone network, the telephone company may

temporarily disconnect service. The telephone company also

retains the right to make changes in facilities and services

that may affect the operation of this equipment. When such

changes are necessary, the telephone company is required to

give adequate prior notice to the user.

However, if advance notice is not possible, the telephone

company will notify the customer as soon as possible. Also,

the customer will be advised of his/her right to file a complaint

with the FCC if he/she believes it is necessary.

WARNING

The Telephone Consumer Protection Act of 1991 makes it

unlawful for any person to use a computer or other electronic

device, including FAX machines, to send any message unless

such message clearly contains in a margin at the top or

bottom of each transmitted page or on the first page of the

transmission, the date and time it is sent and an identification

of the business or other entity, or other individual sending the

message and the telephone number of the sending machine

or such business, other entity, or individual.

(The telephone number provided may not be a 900 number

or any other number for which charges exceed local or long-

distance transmission charges.)

NOTE

In order to program this information into your machine, you

should complete the procedure for registering your name,

unit’s telephone number, time, and date in the Starter Guide.

Users in Canada

Pre-Installation Requirements for Canon Facsimile Equipment

A. Location

Supply a suitable table, cabinet, or desk for the machine.

See Chapter 11, “Appendix,” for specific dimensions and

weight.

B. Order Information

1. A single telephone line (touch-tone or rotary) should be

used.

2. Order a CA11A modular jack, which should be installed

by the telephone company. If the CA11A jack is not

present, installation cannot occur.

3. Order a normal business line from your telephone

company’s business representative. The line should be

a regular voice grade line or an equivalent one. Use one

line per unit.

DDD (Direct Distance Dial) line

-or-

IDDD (International Direct Distance Dial) line if you

communicate overseas

NOTE

Canon recommends an individual line following industry

standards, i.e., 2,500 (touch-tone) or 500 (rotary/pulse dial)

telephones. A dedicated extension off a PBX (Private Branch

eXchange) unit without “Call Waiting” can be used with your

facsimile unit. Key telephone systems are not recommended

because they send nonstandard signals to individual

telephones for ringing and special codes, which may cause a

facsimile error.

C. Power Requirements

The power outlet should be a three-prong grounded

receptacle (Single or Duplex). It should be independent

from copiers, heaters, air conditioners, or any electric

equipment that is thermostatically controlled. The rated

value is 115 volts and 15 amperes. The CA11A modular jack

should be relatively close to the power outlet to facilitate

installation.

Canon MF4450 Image Class Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info