Bedienungsanleitung Canon VB-M641VE (Seite 97 von 287) (Englisch)

683274

Zoom out

Zoom in

Vorherige Seite

1/287

Nächste Seite

Setting Page

[Upload]

Select whether to upload with HTTP or FTP.

[Video Format]

Select the video format for upload. [H.264(2)] cannot be used.

Video size and quality of the uploaded video follow the settings in [Video Settings] (P. 72).

[Frame Rate]

Enter the maximum frame rate of video to be uploaded when [Video Format] is set to [JPEG].

[Pre-event Buffer (number of frames)] (JPEG)/ [Pre-event Buffer (sec)] (H.264(1))

Enter the number of frames or seconds of video to be buffered before the event.

Enter the maximum number of frames for [JPEG] or the maximum number of seconds for [H.264(1)] in [Video Format].

[Post-event Buffer (number of frames)] (JPEG)/ [Post-event Buffer (sec)] (H.264(1))

Enter the number of frames or seconds of video to be buffered after the event.

Enter the maximum number of frames for [JPEG] or the maximum number of seconds for [H.264(1)] in [Video Format].

Note

If the server or network load increases due to the upload settings, the video frame rate may drop. If this occurs, reconfigure the following

settings to reduce the size and frequency of uploaded data.

• Set a lower value for [Video Size: Upload / Memory card] for [JPEG] (P. 73).

• Reduce the number of frames or seconds in [Pre-event Buffer] or [Post-event Buffer] (P. 97).

• If [Volume Detection Event] is enabled, disable [ON Event Operation], [OFF Event Operation] or [Ongoing ON Event Operation] (P. 107).

• From the Intelligent Function Setting Tool [Event] tab, disable [ON Event Operation], [OFF Event Operation] or [Detected mode

Operation] (P. 227).

• If [External Device Input Event] is enabled, disable [Active Event Operation], [Inactive Event Operation] or [Ongoing Active Event

Operation] (P. 105).

• If [Timer Event] is enabled, increase the value in [Repeat Interval] (P. 110).

HTTP Upload

Settings for the HTTP upload function when [Upload] is set to [HTTP Upload].

The HTTP upload function sends notifications via HTTP or via HTTP with attached videos, depending on the network

camera event.

For information about the HTTP upload function and settings, contact your nearest Canon Customer Service Center.

Important

For H.264(1), the following settings must be configured in [Video Settings] > [H.264(1)] (P. 73).

– [Bit Rate Control]: [Use bit rate control]

– [Target Bit Rate (kbps)]: [3072] or less

– [I Frame Interval (sec)]: [0.5], [1] or [1.5]

Important

The maximum video buffer size capacity is approx. 5 MB. If a large video size is set, the Frame Rate, Pre-event Buffer and Post-event

Buffer may not be achieved as specified.

If buffering cannot be achieved as specified, a message is written to the log (P. 134). Confirm that no messages appear in the log.

R11

M641

M741

R11

M641 M741

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon VB-M641VE Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon VB-M641VE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info