Bedienungsanleitung Canon WUX500ST (Seite 17 von 202) (Englisch)

709671

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector.

Failure to do so may cause a fire, electric shock or personal injury.

• Do not look directly into the exhaust vents during use.

• Do not insert any object into vents in the projector, such as the air intake vent

or exhaust vents.

• Do not place a pressurized can in front of the exhaust vents. The pressure of

the contents of the can may increase due to heat from the exhaust vents and

this could result in an explosion.

• When cleaning off dust or dirt from projector parts such as the lens or filter,

never use any spray that is flammable. Internal parts that become hot may

ignite and cause a fire.

• Do not use adhesives, lubricants, oils, or alkaline detergents for

maintenance of the projector. They could adhere to the cabinet and damage

it, possibly resulting in the projector falling from its mounting and causing an

accident or personal injury.

• As strong light beams are emitted while the

projector is in use, do not look directly into the

projector lens. Doing so could cause an eye

injury. Pay particular attention to prevent

small children from doing so.

• Light from the projector is classified as Risk Group 2 (RG2) according to

IEC 62471-5:2015.

• If children may approach the projector or touch it, always ensure the

projector is used under adult supervision.

• Do not hold or install optical instruments (such as magnifying glasses,

reflectors, or glasses) in the path of light from the projector. If projected light

is refracted or reflected and enters people’s eyes, it may result in eye injury.

• When setting the projector on a high surface for projection, be sure the

surface is flat and stable.

• Do not use the projector on a soft surface such as carpet or sponge mat, etc.

• Be sure to ask a qualified technician or the Canon Customer Support Center to

perform the installation work. Poor installation work could result in an accident.

• For ceiling mounting precautions, refer to the installation manual included

with the ceiling mount (Part No.: RS-CL16, sold separately).

Precautions on the Lamp

This projector uses a high-pressure mercury lamp, which must be handled carefully and

correctly as described below.

The mercury lamp has the following characteristics.

• The lamp will gradually become darker over time.

• Impact, abrasion, or use of worn-out lamps may cause lamps to rupture (accompanied

by a loud noise) or burn out.

• Lamps are more likely to rupture after the lamp replacement message is displayed (see

“Replacing the Lamp” (P174)). Replace the lamp with a new one as soon as possible.

• Useful life of lamps varies widely from lamp to lamp and depending on the environment

of use. Some lamps may fail or rupture soon after they are first used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon WUX500ST Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon WUX500ST

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info