Bedienungsanleitung Canon XF200 (Seite 176 von 246) (Englisch)

615742

176

Zoom out

Zoom in

Vorherige Seite

1/246

Nächste Seite

Connecting to a Wi-Fi Network

176

Manual Setup

If you prefer, you can enter manually the details of the Wi-Fi network you want to connect to. Follow the

instructions on the screen to complete the procedure.

1 Open the [Set Up New] submenu.

[w Other Functions] > [Network Settings] > [Connection Settings]

> [Set Up New]

2 Select the [Manual] method.

[Wi-Fi] > [Infrastructure] > [Manual]

3 To enter the [SSID] (network name), select [Input] and then press

SET.

• Enter the SSID (network name) of the selected Wi-Fi network using

the keyboard screen (A 175).

4 Select the Wi-Fi network’s authentication method and then press SET.

• If you selected [Shared Key], skip to step 6.

5 Select the Wi-Fi network’s encryption method and then press SET.

• If the authentication method is [Open], you can select [WEP] and continue to step 6, or [No encryption] and

skip to step 7.

• If the authentication method is [WPA-PSK] or [WPA2-PSK], you can select [TKIP] or [AES].

6 Enter the encryption key as described in Encrypted Access Points (A 175).

7 Continue with the procedure to configure the IP address assignment (A 177).

Camera Access Point

In this mode the camcorder itself serves as a wireless access point to which other Wi-Fi-enabled devices can

connect. Initially, basic default network settings for a Camera Access Point connection are saved under network

configuration [No.1]. After selecting this network configuration (A 179), you can check the default settings

(SSID, password, etc.) on the status screens (A 217) and use them to connect immediately to the camera.

If you prefer to add a network configuration using different settings, follow the procedure below.

1 Open the [Set Up New] submenu.

[w Other Functions] > [Network Settings] > [Connection Settings]

> [Set Up New]

2 Select the [Camera Access Point] method.

[Wi-Fi] > [Camera Access Point]

3 To enter the [SSID] (network name), select [Input] and then press

SET.

• Enter the SSID (network name) the camcorder will use as a Wi-Fi

access point using the keyboard screen (A 175).

• The network name is needed to connect the network device to the

camcorder. If necessary, write it down.

4 Select the channel and then press SET.

5 Select the encryption method and then press SET.

• If you selected [Open/No encryption], skip to step 7. If you selected [WPA2-PSK/AES], continue with step 6.

6 Enter the encryption key as described in Encrypted Access Points (A 175).

• This encryption key (password) is needed to connect the network device to the camcorder. If necessary,

write it down.

[w Other Functions]

[Network Settings]

[Connection Settings]

[Set Up New]

[w Other Functions]

[Network Settings]

[Connection Settings]

[Set Up New]

COPY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon XF200 Seite 176

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon XF200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info