Bedienungsanleitung Canon XF200 (Seite 230 von 246) (Englisch)

615742

230

Zoom out

Zoom in

Vorherige Seite

1/246

Nächste Seite

Troubleshooting

230

Unable to complete WPS. Try the operation again.

- More than 2 minutes passed between activating WPS on the access point and selecting [OK] on the camcorder. Start

over the WPS procedure from the beginning.

- The WPS button was not held down long enough. Refer to the instruction manual of your wireless router. When using

WPS to make a wireless connection, keep the WPS button held down until the wireless router’s WPS function is

activated.

Unable to connect

- Could not connect to the access point or network device selected.

- Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using

the camcorder in a location farther away from such appliances.

Unable to obtain an IP address

- If you are not using a DHCP server, connect using the [Manual] option and enter the IP address using the [Manual]

option (A 177).

- Turn on the DHCP server. If it is already on, make sure it is functioning properly.

- Make sure the address range for the DHCP server is sufficient.

- If you are not using a DNS server, set the DNS address to [0.0.0.0].

- Set the DNS server’s IP address in the camcorder.

- Turn on the DNS server. If it is already on, make sure it is functioning properly.

- Make sure that the DNS server’s IP address and the name for that address are correctly configured.

- If you are using a wireless gateway router, make sure all of the devices in the network, including the camcorder, are

configured with the correct gateway address.

Wi-Fi authentication unsuccessful

- Check the access point’s authentication/encryption method and encryption key and change the camcorder’s Wi-Fi

settings (A 180) as necessary.

Wi-Fi cannot be used while the wireless microphone is attached.

- Wi-Fi connections cannot be used while an optional WM-V1 Wireless Microphone is attached to the camcorder.

Disconnect the WM-V1 from the camcorder and turn it off.

Wi-Fi error. Incorrect authentication method

- Check the access point’s authentication/encryption method and change the camcorder’s Wi-Fi settings (A 180) as

necessary.

Wi-Fi error. Incorrect encryption key.

- When the authentication mode was set to [WPA-PSK] or [WPA2-PSK], or the encryption method was set to [WEP], the

encryption key (WEP index) entered or its length (number of characters) is incorrect.

• When entering ASCII characters, enter 5 characters (64-bit encoding) or 13 characters (128-bit encoding). When

entering hexadecimal characters, enter 10 characters (64-bit encoding) or 26 characters (128-bit encoding).

Wi-Fi error. Incorrect encryption method

- Make sure the camcorder and access point are using the same authentication/encryption method.

COPY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon XF200 Seite 230

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon XF200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info