709292

Canon XF705 Seite 210

210
Zoom out
Zoom in
Vorherige Seite
1/231
Nächste Seite
Troubleshooting
210
Invalid operation
- The following are not valid operations and cannot be performed.
• Trying to add a shot mark to a frame that already has one.
• Trying to add an $ mark and a % mark to the same clip.
•Pressing the REC button when no cards are inserted in the camcorder.
Management file error
- Cannot record because the camcorder cannot write to the file control information. This may occur if the files on the
card were accessed using another device. Save your clips (A 151) and initialize the card (A 35).
May not be possible to record clips on this media
- The card selected for recording has a Speed Class rating lower than 10. Use a recommended card (A 33).
Media full
-The S D card is full. Replace the card or delete some recordings (A 140, 182) to free some space on the card.
Media is almost full
- The amount of available space on the SD card is low. Replace the card or delete some recordings (A 140, 18
2) to free
some space.
- The amount of available space on SD card A and SD card B combined is low. Replace the card that is not selected.
Media is not supported
- 512 MB or smaller SD cards cannot be used with the camcorder. Use a recommended card (A 33).
Memory card is write-protected
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
Number of clips already at maximum
- The card selected for recording already contains the maximum number of clips (999 clips). Replace the card.
Number of Shot Marks at maximum
-The shot mark could not be added because the clip already contains 100 shot marks.
Recorded at 50.00 Hz/59.94 Hz SD Card A / SD Card B: Recommend checking the data and initializing
- The card contains clips that were recorded using a system
frequency different from the one currently used by the
camcorder. Save the content of the card if necessary and initialize the card with this camcorder (A 35).
Recording was stopped.
- The file control information is corrupted or there was an encoder error. Turn the camcorder off and then on again.
Then, remove the card being used and reinsert it. Alternatively, replace the card. If this does not solve the problem,
consult a Canon Service Center.
SD Card A / SD Card B: Check the data.
- Cannot access the card. Check the card and make sure it is inserted correctly.
- A card error occurred. The camcorder cannot record or display the image. Try removing and reinserting the card, or
use a different card.
-You inserted a MultiMedia Card (MMC) into the camcorder. Use a recommended SD card (A 33).
- If after the message disappears,
or appears in red, perform the following: Turn off the camcorder and remove
and reinsert the card. If
6
or
7
turns back to green you can resume recording/playback. If the problem persists,
save your clips (A 151) and initialize the card (A 35).
SD Card A / SD Card B: Recommend checking the data and initializing
- The card cannot be used for any of the following reasons. Save your clips (A 151) and initialize the card (A 35).
•A problem has occurred with the card.
• The camcorder cannot read the data on the card.
•The card was initialized using a computer.
•The card is partitioned.
-The card was initialized using a camcorder with a different firmware version. To be able to record on the card, save the
recordings it contains and then initialize it using this camcorder.
SD Card ASD Card B / SD Card BSD Card A Switched
- The camcorder switched to recording on the other card after you pressed the SLOT SELECT button or automatically
due to relay recording.
SD Card ASD C
ard B / SD Card BSD Card A Will switch in a moment
-The selected card is almost full so the camcorder will switch to recording on the other card in approximately 1 minute
(relay recording).
Some clips require data recovery.
-The power may have been suddenly turned off or the card may have been removed while the camcorder was
recording. As a result, one or more clips contain corrupted data. You can try to recover the clips (A 37).
… 210 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Canon XF705 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Canon XF705

Canon XF705 Bedienungsanleitung - Deutsch - 238 seiten

Canon XF705 Bedienungsanleitung - Holländisch - 229 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info