Bedienungsanleitung Canon XHG1 (Seite 4 von 155) (Englisch, Französisch, Spanisch)

543015

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

25. Outdoor Antenna Grounding — If an outside antenna

is connected to the product, be sure the antenna is

grounded so as to provide some protection against

voltage surges and built-up static charges. Section

810 of the National Electrical Code, ANSI / NFPA No.

70—1984, provides information with respect to

proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location

of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding

electrode. See figure 1.

26. Lightning — For added protection of this product

during a lightning storm, or when it is left unattended

and unused for long periods of time, disconnect it

from the wall outlet and disconnect the antenna. This

will prevent damage to the product due to lightning

and power-line surges.

27. Power Lines — An outside antenna system should not

be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can

fall into such power lines or circuits. When installing

an outside antenna system, extreme care should be

taken to keep from touching such power lines or

circuits as contact with them might be fatal.

28. Overloading — Do not overload wall outlets and

extension cords as this can result in a risk of fire or

electric shock.

29. Objects and Liquid Entry — Never push objects of

any kind into this product through openings as they

may touch dangerous voltage points or short out

parts that could result in a fire or electric shock. Be

careful not to spill liquid of any kind onto the product.

30. Servicing — Do not attempt to service this product

yourself as opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

31. Damage Requiring Service — Disconnect this product

from the wall outlet and all power sources including

battery, and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged.

b.If any liquid has been spilled onto, or objects have

fallen into, the product.

c. If the product has been exposed to rain or water.

d.If the product does not operate normally even if you

follow the operating instructions. Adjust only those

controls that are covered by the operation

instructions. Improper adjustment of other controls

may result in damage and will often require

extensive work by a qualified technician to restore

the product to its normal operation.

e. If the product has been dropped or the cabinet has

been damaged.

f. When the product exhibits a distinct change in

performance. This indicates a need for service.

32. Replacement Parts — When replacement parts are

required, be sure the service technician has used

replacement parts that are specified by Canon or that

have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock or other hazards.

33. Safety Check — Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product

is in safe operating order.

34. Heat — The product should be situated away from

heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that produce

heat.

Fig.1

ANTENNA LEAD IN WIRE

ELECTRIC SERVICE

EQUIPMENT

GROUND CLAMP

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

NEC - NATIONAL

ELECTRICAL CODE

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL

CODE

When replacement of power supply is required, please return it to the responsible nearest Canon Service Center and please

replace it with the same type number CA-920.

The Adapter can be used with a power supply between 100 and 240 V AC. Contact your Canon dealer for information about plug

adapter for overseas use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon XHG1 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon XHG1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info