Bedienungsanleitung Carat A-16 (Seite 15 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

816494

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

Overload protection

To protect the motor, operator and diamond drill, the ma-

chine is provided with a mechanical, electronic and ther-

mal overload safety system. Whenever the engine is swit-

ched o󰀨 due to overload, it must be switched on again as

soon as possible to cool the engine. Then let the drill turn

for a minimum of 1 minute.

1 - Electronic / Thermal

Whenever the engine is heavily overloaded , the overload

indication (LED) on top of the handle will start ashing. The

pressure on the diamond drill bit must than be reduced.

When the motor is overloaded too long, the LED ashes

continuously and the machine will switch o󰀨 automatically.

2 - Mechanical

If the drill bit suddenly gets stuck, the slip coupling is acti-

vated to disconnect the main axis from the engine. Make

sure you switch o󰀨 the engine immediately and remove the

drill from the hole. When the slip coupling is activated for

a longer periods, the mechanical slip must be re-tuned by

a recognised expert.

Drilling with water cooling - Water connection

IF APPLICABLE

The drilling machine is equipped with a water tap, which

includes a ‘Gardena’ connection. Make sure that the core

drill is su󰀩ciently cooled and that the slurry is properly

discharged. The maximum permitted water pressure is 3

bars. Always use clean water to enlarge the life span of

the internal water seals. In case of leakage, the drilling

machine has to be checked IMMEDIATELY by a certied

mechanical expert.

Dry drilling - Dust Extraction

IF APPLICABLE

For dry drilling only use designated drill bits. Dry drilling is

only possible in masonry, brick/block and sandstone.

Dust released during dry drilling is dangerous to your he-

alth. Therefore a dust extraction system specially intended

for this purpose must be used, and if necessary, a dust

mask worn. The use of a dust extraction system is also

required to optimize the life time of the diamond drill bit. To

prevent clogging of the dust extraction system it is essenti-

al that the materials which are being drilled are completely

dry. Information about dust extraction systems is available

at your diamond tools supplier.

Dustec ® dust extraction

The A-1810DT is equipped with an integrated Dustec ®

dust extraction system which is only suitable for Dustec ®

drill bits (with dust holes in the top ange) of max. Ø82 mm

and M16 (F) connection.

The drill bit can be mounted directly on the output shaft. To

remove the drill bit xate the output shaft with a spanner

24. Then loosen the drill bit with a spanner 24, through the

hose connection of the dust extraction.

The dust released during drilling is dangerous to your he-

alth. The A-1810DT is therefore only to be used in combi-

nation with a suitable vacuum cleaner, which is connected

to the hose connection on the Dustec® system.

NASTROC ® system

The A-1821 is equipped with the robust NASTROC ® sy-

stem and the diamond drill can be changed without using

other tools. The lock nut has to loosened, so that the dia-

mond drill with NASTROC ® connection can be assem-

bled.

ENVIRONMENTAL PROTECTION

According to the European regulation 2012/19/

EU, CARAT is responsible to recycle old electric

drill motors. You are therefore requested to re-

turn old CARAT electric drill motors to your local

reseller.

WARRENTY

For the machine, a guarantee period of 12 months applies

from the moment of delivery. Guarantee claims must be

shown by submission of purchase invoice. The guarantee

includes the repair of defects which have occurred and can

be linked by to material or manufacturing faults.

Not covered by guarantee:

• Defects or damages which have arisen due to incorrect

use or connection.

• Machine overload.

• When maintenance has been carried out incorrectly or

badly.

• Information in the manual has not been properly follo-

wed.

• The machine is used by unqualied persons.

• If the machine is used for purposes for which it is uns-

uitable.

• The machine is repaired using unoriginal parts.

• If the machine encryption is damaged or deleted.

• If defects are caused by re, damp and/or transport.

EMISSION

The measured average vibration is less then 2,5 m/s².

Typically the A-weighted noise levels of the pro-

duct are: Sound pressure level 82 dB(A); Sound

power level 92 dB(A). Uncertainty K = 3 dB.

Measured values determined according to EN 62841.

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is

in conformity with the following standards or standardized

documents:

EN 62841-1; EN 61000; 2006/42/EC; 2014/30/EC;

2011/65/EU

Director: C.J. van Beek

22-06-2022

CARAT Nederland B.V.

Nikkelstraat 18, 4823 AB Breda , The Netherlands

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat A-16 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info