Bedienungsanleitung Carat CARACOUP 60 (Seite 22 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

816451

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Before every transport:

- The cutter head must be locked.

- The cutter head must be lowered and locked.

- The cutting table must be secured by the table lock

(for table saw machines).

- The machine must be disconnected from power supply.

- The legs of the machine must be closed.

Due to two transport rollers, the machine can be

transported by one or two persons who can use transport

handles.

Instruction of using crane liing eyes

The machine is designed for crane transport by means of

the liing eye.

Always check the tighteness of the liing eyes before using

it to transport the machine. To avoid damage, also check

that the liing straps do not touch the motor when liing.

NOTE!

Never move the machine by dragging. Always use

the intented wheels.

CAUTION!

Risk of injury due to improper handle when it is

transported by crane.

CAUTION!

Risk of injury by standing under the machine when

it is transported by crane.

CAUTION!

Risk of injury of falling material from the working

table, it is not allowed to have any material on working

table when it is transported.

Crane liing eyes CARACOUP 104 / CARACOUP 100

. INSTALLATION

5.1 Connection

Before connecting the machine to the power source,

make sure that:

- Voltage / phase of the power supply, match the date on

the type plate of the motor and machine.

- The power supply line is grounded according to the safety

provisions.

- The wire size of the extension cord is suicient, H07RNF

3x2.5 mm² up to 50m for 230V.

5.2 Mounting a diamond blade

To mount a new diamond blade or replace the used one,

proceed as follows:

1. Switch o the machine and interrupt the power supply

by pulling the mains cable from the mains outlet.

2. Loosen the screws on the diamond blade guard so as to

be able to remove the front half of the diamond blade

guard.

3. Loosen the nut of the motor sha and remove the outer

cutter ange.

4. Clean the cutter ange, nut and motor sha.

5. Check the parts for signs of wear.

6. Mount or replace the diamond blade. While doing so,

pay attention to the correct rotation direction of the

diamond blade and motor sha.

7. Replace the outer cutting ange on the motor sha.

8. Screw the nut onto the motor sha again and tighten it

rmly.

9. Replace the front half of the cutting wheel guard to

connect it with the rear half.

10. Tighten rmly the screws on the cutting wheel guard.

NOTE!

The arrow on the cutting wheel indicates

correct rotation direction.

NOTE!

The cutting wheel, irrespective of its position or

the position of the cutter head, may not touch the table!

5.3 Mounting the transport handles and wheels

Mount the transport handles at the appropriate places on

the base frame using the supplied washers (4x A8,4 ISO

7089) and the screws (4x M8x30 ISO 4017), the spring wash-

ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).

Do the same with the transport wheels. Mount the trans-

port wheels at the appropriate places on the base frame

using the supplied washers (4x A,8,4 ISO 7090), the spring

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat CARACOUP 60 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info