Bedienungsanleitung Carat MultiCoup 350 (Seite 20 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

816479

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

In case of storage for over 3 months, check general

condition of all parts and packaging on a regular basis. If

necessary, renew or replace conservation materials.

 

 

 

Improper transportation can result in considerable dam-

age of the machine and objects in the vicinity.

Before every transport:

- The cutter head must be locked.

- The cutter head must be lowered and locked.

- The machine must be disconnected from power supply.

The machine can be carried by one person on the vertical

column.

 

 





 

5.1 Connection

Before connecting the machine to the power source,

make sure that:

- Voltage / phase of the power supply, match the data on

the type plate of the motor and machine.

- The power supply line is grounded according to the

safety provisions.

- The wire size of the extension cord is suicient, H07RNF

3x2.5 mm² up to 50m for 230V.

5.2 Mountingadiamondblade

To mount a new diamond blade or replace the used one,

proceed as follows:

1. Switch o the machine and interrupt the power supply

by pulling the mains cable from the mains outlet.

2. Loosen the screw on the back of cutting wheel guard

so as to be able to turn the blade guard aside.

3. Loosen the nut of the motor sha and remove the

outer cutter flange.

4. Clean the cutter flange, nut and motor sha.

5. Check the parts for signs of wear.

6. Mount or replace the diamond blade. While doing so,

pay attention to the correct rotation direction of the

diamond blade and motor sha.

7. Replace the outer cutting flange on the motor sha.

8. Screw the nut onto the motor sha again and tighten it

firmly.

9. Turn the cutting wheel guard back to its original loca-

tion.

10. Tighten firmly the screws on the back of cutting wheel

guard.

 

 



 

 



 

6.1 Intendedworkingpositionoftheoperator

The operator takes position in front of the machine.

The operator stands in front of the machine so that he

can push the cutting material table forward and back and

adjust the cutting head appropriately.

6.2 Start-uppreparation

To safely use the machine as intended, the following

preconditions must be met:

- The machine stands firmly.

- The water supply via a pressurized water tank or a

standing pipe is guaranteed, or a suitable dust extractor

of class M is connected to the dry cutting method.

- The machine has been checked for damage, loose screw

connections and integrity.

- The water supply is functional.

- Rotation direction arrows on the cutting wheel and

guard match.

- An appropriate cutting wheel must be installed, which

meets optimum conditions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat MultiCoup 350 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info