Bedienungsanleitung Carat MZ-300 (Seite 15 von 24) (Englisch, Holländisch, Französisch)

816471

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH

Prevent overload

Make sure that the rotation speed of the motor does not

drop too much. Allow the diamond cutting blade to cut.

The machine is equipped with a thermal circuit breaker

(#9) that switches the machine OFF in case of overloading.

Aer a short break it can be switched ON again. Please

let the machine run freely for half a minute, allowing the

motor time to cool down.

Should the thermal circuit breaker (#9) switch OFF oen,

we advice you to cut less deep or to put less pressure on

the machine.The thermal circuit breaker is switched OFF

when it is in it’s up-position. It then shows a while line

along the button.

If the thermal circuit breaker (#9) switches the machine o,

the thermal circuit breaker has to be reset. Also the main

ON/OFF switch (#13) has to be switched ON again.

Prevent pooring water in the motor.

In case of horizontal cuts, the motor must be above the

diamond cutting blade.

In case of vertical cuts, the vacuum connection (#1) needs

to be at the bottom of the blade guard. When cutting in

ﬂoors the motor absorbs a lot of water haze. It is advisable

to ﬁx a ﬂexible hose (± Ø 100 mm, length 2 meter) at the

suction opening of the motor so more dry air will be taken

in.

PRACTICAL TIPS

• Determine where you want to have the saw cut. A lath at

2,5 cm (± 1 inch) besides the cut, will simplify the

guidance of the machine.

• Hold the machine, with the edge of the bottom plate

against the wall or ﬂoor so that the diamond cutting

blade is still free. Before pressing the machine into the

material, switch the machine ON and let the diamond

cutting blade run freely to enable it to reach the maximum

speed. Please check if the diamond cutting blade is not

rotating eccentrically and is not swinging.

• Before taking the diamond cutting blade out of the saw

cut, wait until the diamond cutting blade is standing still.

It is dangerous to block or to slow down the turning dia-

mond cutting blade by pushing against the diamond cut-

ting blade.

• Do not cut curves.

• When cutting a ﬂoor, stay in front of the machine

• In case of vertical cuts put in the machine at the top and

lower it by its own weight, guided by hand.

• When using the machine for extended periods of time, the

user could become tired thanks to vibrations. To avoid this

take pauses on a regular base.

EMISSION

Vibration emission value ah = 6 m/s². Uncertainty K

< 2,75 m/s².

The level of the sound pressure for machines,

developed for cutting stone and similar mate-

rials, depends on a lot of factors: type of

diamond cutting blade, the material to be

cut, the use of water.

Typically the A-weighted noise levels of the product are:

Sound pressure level 87,5 dB(A); Sound power level 91,5

dB(A). Uncertainty K=3 dB. Measured values determined

according to EN 60745-1.

ENVIRONMENTAL PROTECTION

According to the European regulation

2012/19/ EU, CARAT is responsible to recycle

old electric drill motors. You are therefore

requested to return old CARAT electric drill

motors to your local reseller.

SERVICE AND MAINTENANCE

The wall-saw machine MZ-300/MZ-350 only

needs a limited maintenance.

• It is desirable to clean the interior with compressed air

aer ﬁnishing the job.

• Make sure the vent hole of the motor is kept free and

clean.

• Checking the machine by a specialist is advisable aer

300 working hours.

• Only use original spare parts.

Changing the carbon brushes

It is desirable to check the wear of the carbon brushes aer

100 eective working hours. Moreover check the carbon

brushes if these can still move freely in the brush holders.

Procedure:

• Pull the plug out from the power supply.

• Loosen the caps by using a screwdriver and take the

carbon brushes out of the machine.

• If necessary, replace the carbon brushes.

• Screw the caps of the carbon brushes into the machine

again.

• Switch the machine ON and leave it running freely, for

approximately 10 minutes, before using it again.

FAILURES

The electromotor doesn’t start up:

1. Check the mains voltage and/or the electrical

connec tion of the motor.

2. Check if the PRCD switch (#15) is in the ON-position

3. Check if the thermal circuit breaker (#9) is not tripped

and does not show a white edge along the button.

4. Check if the cables are correctly connected.

5. Check if the carbon brushes aren’t worn out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat MZ-300 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info