Bedienungsanleitung Cardo scala rider fm (Seite 9 von 12) (Englisch)

232599

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

English

scala rider

™

your headset for three seconds to turn on the radio. The radio tunes

in to the last radio station you were listening to. With some phones

you should wait a few seconds after ending a call before turning on

the Radio.

Turning the FM Radio O

While the radio is turned on, press and hold the Radio Button for

three seconds to turn the Radio o.

Switching Preset FM Radio Station

There are six pre-set Radio stations available on your scala rider FM.

While the Radio is on, tap the Radio Button to cycle between saved

stations.

Searching for a New FM Radio Station

While the Radio is on, press and hold the Volume Up or Volume

Down Button for three seconds or until you hear the next station on

your headset.

Pressing Volume Up will search upwards (higher frequency). Pressing

Volume Down will search downwards (lower frequency). Once a

station is found, searching stops and you can hear the station.

To save this station, refer to the following section.

To continue searching, press the Volume Up or Volume Down Button

again for three seconds.

You may still continue to listen to the current unsaved station.

Pressing the Radio Button in this case will switch to the next saved

station.

Saving an FM Radio Station

The FM Radio is equipped with a memory capacity of six stations.

• Select the station you wish to replace by tapping the Radio

Button until you nd the station you want to replace.

• Search for a new station as described above.

• Tap the Radio Button within 20 seconds of nding the station to

save the current station.

If you don't save the station, the Radio will exit search mode without

saving the current station. You can still continue to listen to the

current unsaved station. Tapping the Radio Button in this case will

move to the next saved station.

USING THE MP3 PLAYER WITH YOUR

HEADSET

Your scala rider FM headset can be connected to an MP3

player device by plugging it to the Helmet Clamp’s jack with

the MP3 cable.

In order to secure the MP3 cable tightly into place, please proceed as

follows:

1. Use the enclosed Allen Wrench to remove both Allen screws from

Helmet clamp and release the clamp’s back plate.

2. Place the MP3 cable holder on the helmet clamp. Both pins on the

MP3 cable holder should be xed into corresponding indentations

on clamp.

3. Place the Back Plate on top of the MP3 cable holder and secure

all parts together using the Allen screws that were previously

removed, as shown in photo.

4. Attach the clamp and headset onto

your helmet as described previously

in section “ATTACHING THE CLAMP

ON THE HELMET”.

5. Attach the speakers to your helmet as

described in section ”POSITIONING

THE SPEAKERS”.

MP3 cable holder hook

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cardo scala rider fm Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cardo scala rider fm

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info