Bedienungsanleitung Cardo Scala rider G4 (Seite 16 von 27) (Englisch)

480782

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

9.6 VOICE CONNECT FEATURE VOX

The G4 oers VOX technology for safe and hands-free operation of

some key functions.

For incoming calls, just pronounce loudly any word (e.g. “hello”).

To reject an incoming call, remain silent for about 15 seconds.

To reject an Intercom call remain silent for 30 seconds.

NOTE: The Enable/Disable Voice Connect feature aects only the Intercom

functionality.

ENABLE/DISABLE VOX can be done via the PC software and directly

on your G4 via the Settings Customization Voice Menu (see section 4.2).

9.7 RESET PAIRING RESTORING THE ORIGINAL DEFAULT

CONFIGURATION

This section is only relevant once you have completed a pairing process

You can delete all of your paired devices at any time as follows:

1. With the G4 turned ON, press and hold the Mobile Button for

at least six seconds until the Red and Blue Lights begin rapidly

alternating.

2. Press and hold the Volume Up Button for three seconds.

3. The Red and Blue Lights will flash five times simultaneously and

then the G4 will turn off, confirming that Reset was successfully

completed.

9.8 NOTEWORTHY ISSUES

a. Connecting the G4 to other units

To pair your G4 to other scala rider models, please refer to section

9.10 c below.

b. Busy Status (When using a G4)

When attempting an Intercom call with a device that is already on

a Phone/GPS/Intercom call, you will hear two beeps indicating the

other device is busy.

c. Automatic Reconnection of the Intercom

If the G4 and another paired unit go out of range and disconnect

from each other, the G4 will immediately try to reconnect to the

other unit.

You can manually reconnect the intercom call while the G4 is in

Standby mode by pressing the CHANNEL “A” or the CHANNEL “B”

Button to connect to the respective lost connection.

d. Conference Mode Limitations

Whenever you enter the Intercom Conference mode among three

or even four participants (including yourself), the participants

who maintain simultaneously two active connections will not be

able to receive mobile phone calls or GPS messages as long as the

conference call is in progress (see details in sections 9.10 b and 9.10 c)

9.9 TROUBLESHOOTING THE INTERCOM

First, make sure your microphone is located properly in front of the

center of your mouth.

The G4 is designed for use in loud environments. Therefore, you

should test the Intercom functionality only in a noisy environment,

such as next to an idling motorcycle and not indoors. Please also

verify that the G4s were paired together properly by following the

instructions in the relevant Setup sections.

9.10 USING THE G4 FOR INTERCOM WITH OTHER G4 UNITS

PAIRING LED INDICATION FOR INTERCOM CHANNELS

INTERCOM

CHANNEL

PAIRING / CONNECTION

BUTTON

PAIRING MODE LED

INDICATORS

CHANNEL “A” CHANNEL “A” BUTTON Rapid RED ashing

CHANNEL “B” CHANNEL “B” BUTTON Rapid BLUE ashing

scala rider

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cardo Scala rider G4 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cardo Scala rider G4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info