Bedienungsanleitung Cardo Scala rider G4 (Seite 20 von 27) (Englisch)

480782

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

9.11b. TWO-WAY INTERCOM WITH EARLIER SCALA RIDER

MODELS

To use your G4 with other scala rider models such as the “Solo”,

“FM”, “TeamSet pro” or a “TeamSet” Driver unit make sure you have the

manual of the other scala rider headset available.

1. While the G4 is turned OFF, turn it ON by pressing and holding the

Mobile Button until the Blue Light ashes three times.

2. Turn the other scala rider ON by pressing and holding its CTRL

Button until the Red/Blue lights begin rapidly alternating.

3. For the G4, select an available CHANNEL to pair the other unit

(CHANNEL “A” or CHANNEL “B”).

NOTE: Selecting a CHANNEL that is already in use will replace the paired

device on that CHANNEL with the newly paired headset.

4. On the G4, press and hold the assigned CHANNEL BUTTON (“A”

or “B”) for at least six seconds until the BLUE or RED Light begins

ashing rapidly, indicating it is in Intercom Pairing mode. (See 9.10

Intercom Channel Table for details)

5. Within a few seconds, the G4 will show a solid light for two

seconds, indicating that the two units are now paired, connected

and ready for use.

NOTES:

• If the Pairing process is not completed within two minutes the units will

return to Standby mode.

• When using an earlier scala rider model to serve as the Passenger unit

(e.g. a “Solo”, “FM”, “TeamSet pro” or a “TeamSet” Driver unit), Voice

Connect Intercom can only be initiated from the G4. However, you can

always initiate the Intercom manually also from the other scala rider

unit by pressing the button.

Initiate Intercom calls from scala rider G4

There are two ways to start an Intercom call with your paired headsets

while the G4 is in Standby mode:

VOICE CONNECT:

Start talking loudly

Once you start talking loudly, an

Intercom call will be established with

both paired headsets.

The Intercom call will stay on until all

participants remain silent for 30 seconds.

CHANNEL BUTTON

CONNECT:

Single tap the chosen

Channel Button to add or

remove the unit from an

Intercom call.

Initiate Intercom calls from:

Q2 pro: Tap the MC Button once on a Q2 pro unit to open an intercom

call. To terminate the call, tap once.

Q2: Tap the MC Button twice on a Q2 unit to open an intercom call.

Wait 3 seconds between taps. To terminate the call, tap once.

Other scala rider models: Tap the headset CTRL Button to open/

close intercom call.

9.11c. THREE WAY INTERCOM WITH OTHER SCALA RIDER

MODELS

In terms of range, the 3-Way Intercom between your G4 and

other scala rider units achieves distances of the lowest common

denominator. For example, connecting your G4 with two Q2 pro units

will enable intercom distances of maximum 2,300 ft / 700m.

NOTE: When connected to earlier scala rider headsets (e.g. a “Solo”, “FM”,

"TeamSet pro" or a “TeamSet” Driver unit) only Rider-to-Passenger mode is

available.

All options are in Full Duplex, meaning that all parties can speak and

hear one another simultaneously, similar to mobile or landline phone

conversations and unlike walkie-talkie communications.

scala rider

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cardo Scala rider G4 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cardo Scala rider G4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info