Bedienungsanleitung Cardo Scala Rider Q3 MultiSet (Seite 9 von 14) (Englisch)

667725

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

6. PAIRING AND USING A MOBILE PHONE,

GPS DEVICE OR MP3 PLAYER

To connect your scala rider to a Bluetooth device you must rst pair

them. Once paired, they will automatically recognize each other

whenever they are within range (10m / 33ft).

Your scala rider has two Bluetooth channels for connection to

mobile phones, GPS devices and music players with A2DP.

6.1 PAIRING BLUETOOTH CHANNELS 1 AND 2

1. Make sure Bluetooth is enabled on your phone/GPS/MP3 player.

2. Check the scala rider is in Standby.

3. To pair Bluetooth Channel 1 – press

for at least 5 seconds

until the RED and BLUE LEDs begin rapidly alternating.

To pair Bluetooth Channel 2 – press

for at least 5 seconds

until the RED and BLUE LEDs begin rapidly alternating.

To pair a GPS, when LEDs begin rapidly alternating, tap .

4. Search for Bluetooth devices on your phone/GPS/MP3 player by

following the device’s instructions.

5. After a few seconds the device will list “scala rider Q3 ”. Select it.

6. If prompted for a PIN or Passkey, enter 0000 (four zeros).

7. The device will conrm that pairing has succeeded and the LED

will begin ashing slowly in BLUE.

8. If Pairing is not completed within 2 minutes, the scala rider will

return to Standby.

• If you have paired 2 dierent mobile phones directly to your scala rider ,

you will need to set one as default for making calls.

• If your GPS supports it, you can pair the second mobile phone directly

to the GPS and then pair the GPS to your scala rider, and so connect

both mobile phones and the GPS to your scala rider.

• Not all Bluetooth mobile phones can broadcast Bluetooth Stereo music

(A2DP), even if the phone has an MP3 player function. Consult your

mobile phone’s User Manual for more information.

• Not all Bluetooth GPS devices allow connection to Bluetooth audio

devices. Consult your GPS User Manual for more information.

• After pairing, you may need to tap

to connect the scala rider .

6.2 MAKING AND RECEIVING PHONE CALLS

Answer a call

Tap

or say any word loudly to answer by VOX

Reject a call Remain silent for 15 seconds, or press and hold

for 2 seconds

End a call

Tap

Voice Dial

(if supported by

mobile phone)

Tap

and

simultaneously and follow the

prompt from the mobile

Redial

Press

and

for 2 seconds

Hot-Dial

Tap

three times

Set default phone

When on a phone call, press

for 5 seconds

Toggle default

phone

In Standby, press

for 5 seconds

This feature is not available during mobile calls

To use the Hot-Dial, rst congure the number (see section 3).

If you have 2 mobile phones paired directly to your scala rider, you will need to set one of them to use as

default for outgoing calls.

| scala rider

Q3 / Q3 MultiSet™

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cardo Scala Rider Q3 MultiSet Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cardo Scala Rider Q3 MultiSet

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info