Bedienungsanleitung Cardo scala-rider TeamSet (Seite 6 von 12) (Englisch)

497568

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ATTACHING THE CLAMP ON THE HELMET

Perform this procedure for both the driver and the passenger helmets.

The Helmet Clamp must be attached to the left side of the helmet. Once

attached, the headset unit can be mounted or released from the Helmet

Clamp at any time. If you wish to connect your MP3 player to you head-

set, please refer rst to the assembly instructions listed in section: USING

THE MP3 PLAYER WITH YOUR HEADSET.

There are two methods that can be used in order to attach the Clamp

onto the helmet:

Standard Method: Recommended for most helmet types.

Glue Plate Method: Recommended for helmets

to which the standard method cannot be applied,

using the Glue Plate included in the box.

Standard Method

1. Use the enclosed Allen Wrench to loosen the two

screws on the Back Plate.

2. Slide the Back Plate between the internal

padding and the external shell of the helmet.

3. Adjust the clamp’s location so that the

microphone is located opposite center of

your mouth and then tighten the screws.

You may need to reposition the Clamp

repeatedly until you identify the best spot. The microphone

must be positioned vertically and not horizontally.

Glue Plate Method

You have the option to glue the Helmet Clamp onto your helmet, when

the above standard method cannot be used, or in case you prefer to

secure the Helmet Clamp with adhesive glue. This option has been

successfully used for a range of high end helmets.

NOTE: While we have no reason to believe that the gluing

option might negatively affect any helmet, Cardo

does not assume any responsibility to that affect, ir-

respective of its nature and circumstances. The Glue

Plate is offered as a free option that you may choose

to use at your own risk and subject to renouncement

of any future claims.

Caution: This process can be done only once!

1. Use the enclosed Allen Wrench to remove both Allen

screws and release the Helmet Clamp’s back plate.

2. Determine the location on the helmet where the Helmet Clamp

must be attached.

3. Adjust the Helmet Clamp’s location on the

Helmet so that the microphone is located

opposite the center of your mouth. You may

need to reposition the Clamp repeatedly until

you identify the best spot. The microphone must

be positioned vertically and not horizontally (Be sure to clean the

selected area prior to the gluing process as described in # 4 below).

4. Use the pre-moistened Towelette to clean the helmet area where

you want to install the Glue Plate. Allow to dry thoroughly.

5. Peel the foil cover from the Glue Plates’ adhesive pad.

6. Place the Glue Plate into position according to #3. Press rmly 15

seconds on all 3 parts of the Glue Plate.

7. The adhesive pad bonds to full strength over the next 24 hours.

Therefore it is recommended to not use the headset during this 24

hour period.

8. Fasten the Clamp to the Glue Plate using the Allen screws that were

previously removed.

scala rider

TeamSet

™

scala rider

TeamSet

™

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cardo scala-rider TeamSet Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cardo scala-rider TeamSet

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info