Bedienungsanleitung Care ANTIS II - 50535 (Seite 15 von 57) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

602718

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

4. The WEIGHT will flash and you can press UP or DOWN keys to set your WEIGHT. Press ENTER key to confirm

your WEIGHT. The default WEIGHT is 70kgs or 155lbs.

5. The GENDER will flash and you can press UP or DOWN keys to select your sex. Number 1 means man and

number 0 means female. Press ENTER key to confirm your Gender. The default sex is 1 (MAN).

6. The AGE will flash and you can press UP or DOWN keys to set your AGE. Press ENTER key to confirm your

AGE. The default AGE is 35.

7. Press the START/STOP key to begin body fat measurement. If the window show E on the window, please make

sure your hands are attached well on the grips or the chest belt is touch well on your body. Then press the

START/STOP key again to begin body fat measurement.

8. After finished your measurement, the computer will show the values of BMR, BMI and FAT PERCENT on the LCD

display. Furthermore, the computer will show your own exercise profile for your body type.

9. Press START/STOP key to begin exercise.

Operation guide:

4. Sleep Mode:

The computer will enter the sleep mode when there is no signal input and no keys be pressed after 4 minutes. You

can press any key to wake up the computer.

5. BMI (Body Mass Index): BMI is a measure of body fat based on height and weight that applies to both

adult men and women.

6. BMR (Basal Metabolic Rate): Your Basal Metabolic Rate (BMR) shows the number of calories your body

needs to operate. This doesn’t account for any activity, it’s simply the energy needed to sustain a heartbeat,

breathing and normal body temperature. It measures the body at rest, not sleep, at room temperature.

Error Message:

E1 (ERROR 1):

Normal state: During workout, when the monitor did not get the count signal from the gear motor more than 4

seconds and check under successive 3 times then the monitor will show E1.

Power on state: The gear motor will return to zero automatically, when the signal of motor cannot be detected for

more than 4 seconds then the gear motor’s driver will be cut off immediately and show the E1 on the LCD display.

All the other digital and function mark are blank, and the output signals are cut off also.

E2 (ERROR 2): When the monitor read the memory data, if the I.D. code is not correct or the memory IC damages

then the monitor will show E2 immediately at power on.

E3 (ERROR 3): After 4 seconds by start mode, the computer detects the faulty motor did not leave the zero point

then the monitor displays “E3”.

Technical data of the current adapter

1. Available for Input: 230V/50Hz or 60Hz Output: 6V AC/0.5A

2. Available for Input: 110V/50Hz or 60Hz Output: 6V AC/0.5A

LCD Workout Graphics

PROFILE of each Program：

PROGRAM 1 (MANUAL)： PROGRAM 2 (STEPS)：

PROGRAM 3 (HILL)： PROGRAM 4 (ROLLING)：

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Care ANTIS II - 50535 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Care ANTIS II - 50535

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info