Bedienungsanleitung Carrera 501003 (Seite 7 von 40) (Alle Sprachen)

551117

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Contents of package

1x Helicopter

1x Controller

1x Charging unit consisting of a USB charging

cable and a USB mains adapter

4x 1.5 V Mignon AA batteries (non-rechargeable)

1x Lanyard

2x Joystick extensions

1x Set of replacement parts

Recharging the LiPo rechargeable

battery

Make sure you only charge the LiPo rechargeable battery

supplied with the LiPo charging unit also supplied (USB

cable and remote control). In case you try to charge the re-

chargeable battery with a diﬀerent LiPo battery charger or

any other battery charger, this might cause serious damag-

es. Please carefully read the previous chapter about warn-

ings and guidelines on the usage of rechargeable batteries

before proceeding.

Charging at the mains socket

• Connect the USB charging cable to the USB

mains adapter. As soon as you connect the

charger unit with the mains socket, the LED on

the USB charging cable lights up green indicating

that the charger unit is correctly connected with

the mains socket.

If you plug in a helicopter with a discharged bat-

tery, the LED on the USB charging cable lights up

red and shows that the helicopter battery is being

charged. The USB charging cable and the charg-

ing socket on the helicopter are designed to make

incorrect connection impossible.

• It takes about 30 minutes to recharge a dis-

charged battery (but NOT a deep-discharged

one). When the battery is fully charged, the LED

display on the USB charger cable lights up green

again.

Charging via computer:

• Connect the USB charging cable with the USB

port of a computer. The LED on the USB charger

cable lights green indicating that the charger unit

is correctly connected to the computer.

If you plug in a helicopter with a discharged bat-

tery, the LED on the USB charging cable lights up

red and shows that the helicopter battery is being

charged.

The USB charging cable and the charging socket

on the helicopter are designed to make incorrect

connection impossible.

• It takes about 30 minutes to recharge a dis-

charged battery (but NOT a deep-discharged

one). When the battery is fully charged, the LED

display on the USB charger cable lights up green

again.

Note: When supplied, the lipo-battery is already partially

charged so the ﬁrst charging cycle may well take less time.

It is essential to follow the connection sequence given

above! If you have the charger cable only connected to

the helicopter, and not to a source of electricity, a green

LED display indicates that there is still power in the bat-

tery. The green LED display does not necessarily indi-

cate the battery is still adequately charged.

While charging, the power switch must be in the “OFF”

position.

Inserting the batteries in the

remote control

Open the battery compartment with a screwdriver

and insert the batteries in the remote control.

Please keep in mind the correct polarity. After

having closed the compartment you can check all

functions of the remote control with the help of the

power-switch on the front. With the power-switch

turned ON and proper functioning, the top center

LED on the remote control will light up red.

When the control LED ﬂashes rapidly, the batter-

ies in the controller must be changed.

Frequency bind between model

and remote control

The Carrera RC helicopter and the remote control

are frequency bound at purchase. Should there

occur any problems with the communication be-

tween the Carrera RC helicopter and the remote

control at the beginning, please carry out a new

frequency bind.

• Connect the plug-in connection at the mod-

el and switch on the model at the ON/OFF

switch.

• The LED in the helicopter now ﬂashes in rhyth-

mically-accelerating sequence.

•

Switch on the controller at the ON/OFF switch.

While connecting, the controller emits a signal tone.

• Place the charged helicopter on a ﬂat surface.

• Allow the helicopter a few moments until the

system is correctly initialised and is ready for

operation.

• The control LED now lights continuously once

again, indicating that the connection is ended.

Checklist for ﬂight preparation

This checklist does not replace the contents of the operating

instructions. Although it can be used as a quick-start-guide

we strongly advise to ﬁrst read the operating instructions in

detail before you proceed.

• Check the contents of the package

• Connect the charging unit to the source of power.

• Charge the lipo-battery as described in the section “Charg-

ing the lipo-battery”.

• Fit four AA batteries in the controller, making sure their po-

larity is correct.

• Look for a suitable environment for ﬂying

• Place the helicopter on a ﬂat surface

• Switch on the model at the ON/OFF switch.

• Turn the remote control on at the ON/OFF switch.

• The LED in the helicopter now ﬂashes in rhythmically-

accelerating sequence.

• During the binding process, the controller emits an acous-

tic signal.

• Allow the helicopter a few moments until the system is cor-

rectly initialised and is ready for operation. The LED in the

helicopter now lights continuously.

• Repeat the above points as required, if you wish to ﬂy more

helicopters at the same time.

• Check the control system

• Make yourself familiar with the control system

• Trim the helicopter as necessary as described under “Con-

trolling the helicopter”, so that when hovering the helicopter

no longer moves from the spot, until given a command by

the controller.

• The helicopter is now ready to be ﬂown.

•

If the helicopter displays no functions, retry the above bind-

ing procedure.

• Fly the model

• Land the model

• Switch the model oﬀ at the ON/OFF switch

• Always switch oﬀ the remote control last

Range of functions of the remote

control

1. Antenna

2. Power switch (ON / OFF)

3. Control LED

4. Gas · tail (spinning in circles)

5. Forward/backward tail (spinning in circles)

6. Trimmer for tail

7. Battery compartment

8. Slot for keeping

Joystick extensions

9. Joystick extensions

to screw on lever 4. & 5.

Description of helicopter

1. Coaxial rotor system

2. Tail rotor

3. Socket for charging the lipo-battery

4. Landing skids

5. ON-/OFF switch

Controlling the helicopter

In case you don´t know the control functions of

your Carrera RC helicopter yet, please take some

minutes before the ﬁrst ﬂight in or to make your-

self familiar with them. The descriptions left or

right refer to the view out of the cockpit (pilote´s

view). Push the throttle up to increase the rota-

tional speed of the main rotor blades. Increase the

rotational speed of the main rotor blades and the

model will start to ascend.

If you push down the throttle and thus reduce the

rotational speed of the main rotor blades the heli-

copter will descend. When the model has lifted oﬀ

the ground you can get it into stationary hovering

without abrupt ascending or descending by care-

fully moving the throttle upwards and downwards.

Move the right lever (tail) to the left and

the helicopter’s nose turns (yaws) round

the main rotor’s axis in a circle to the left.

Move the right lever (tail) to the right and the heli-

copter’s nose turns (yaws) round the main rotor’s

axis in a circle to the right.

Use the trimmer for tail until you have reached a

stable neutral position of the helicopter when hov-

ering, without moving the right lever (tail).

The forward-/backward lever controls the

helicopter´s pitch forward and backward. When

shifting the lever forward the nose of the helicop-

ter will move downwards and the helicopter will ﬂy

forward. When shifting the forward-/backward le-

ver backward the helicopter will move backwards

and the helicopter will ﬂy backward.

After having made yourself familiar with the main control

functions and having chosen an appropriate area for ﬂying

the helicopter, you can start the ﬁrst ﬂight.

Choosing the ﬂight area

When being prepared for the ﬁrst ﬂight you

should choose a closed room without any

persons or obstacles which is as big as pos-

sible. Due to the size and controllability of the

helicopter experienced pilotes may be able to

ﬂy the helicopter in relatively small rooms. For

your ﬁrst ﬂights we strongly recommend to

choose a room with a minimum ﬂoor space of

3 x 3 metres and 2.40 metres of height. After

having trimmed your helicopter for ﬂight and

having made yourself familiar with the control-

ling and its functions you may start ﬂying in

smaller and less open environments.

The helicopter has exclusively been devel-

oped for indoor use in closed rooms.

Information on trouble-shooting will be found on page 36.

For t he latest version of these operating instructions

and information on replacement and spare parts avail-

able, please visit carrera-rc.com in the service area.

Errors and changes excepted

Colours / ﬁnal design – changes excepted

Technical changes and design-related changes excepted

Pictograms = symbolic photos

ENGLISH

Carrera 501003 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info