469918

Carrera Digital 124 - 30352 Control Unit Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
11
Sound ON/OFF








The conrmation sound when crossing the sensors and the key
sound can be switched o. Switch o the Control Unit and keep the
“START/ENTER” button
pushed, switch on the racetrack and
release “START/ENTER”
again. The acknowledgement sound
for switching on the Control Unit cannot be switched o however.
Reset function








To restore the Control Unit to factory settings the Control Unit oers
a reset function.
Switch o the Control Unit and keep the “ESC/PACE CAR”
but-
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
After 20 minutes of non-usage the Control Unit switches to energy-
saving mode and all displays such as Position Tower, Driver Dis-
plays and Startlight are turned o. To reactivate shortly press any
speed controller´s tappet or push lane-change button at the speed
controller or control key at the Control Unit. All settings will be kept.
Starting sequence



Driving without starting sequence:
1. Switch on the Control Unit (ON-OFF)
2. After approx 1 second the central LED lights permanently and a
brief acoustic signal will sound , g
3. Place the car/s on the connecting track
4. In this mode the track is cleared without starting light signal; you
can start immediately.



With the starting sequence being initiated all displays will be reset.
1. Switch on the Control Unit (ON-OFF)
2. After approx 1 second the central LED lights permanently and a
brief acoustic signal will sound , g.
.
3. Then push start button until all LEDs will light, g.
.
4. Place the car/s on the connecting track, g.
.
5. Push start button again - the starting sequence is initiated, the
LEDs are lit and acoustic signals can be heard.
6. With elapse of the starting light procedure (LEDs light individu-
ally) the race is released, g.
.
7. False start: If a car´s speed controller is actuated during the
starting light phase, this is rated as false start. The vehicle having
caused the false start will travel a short distance and the LED on
the relevant car or speed controller will ash. The race will not be
released and the start has to be repeated.
Maintenance and care
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior
to cleaning.
 Keep the track surface and track slots clean with a
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
Troubleshooting
Driving tips

In case of any malfunctions, please check the following:
• Has the connection to the power supply been established correctly?
• Have transformer and speed controllers been connected
correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track‘s current feed will be switched o automatically for 5
seconds, if there is an electrical short circuit: this will be notied by
audible and visual signals.
• Are the cars placed on the track in running direction? In case of
non-functioning push the running direction switch which is on the
car´s bottom.

During operation small car parts as spoilers or mirrors may get o or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.

• You can drive fast along the straight track but you should brake
before the curve and then accelerate again when coming out of the
curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
 When using track systems which are not manufactured by
Carrera the existing guide keel has to be replaced by the special
guide keel (#85309). While using the Carrera crossing (#20587) or
high banked curve 1/30° (#20574) slight driving noise might occur
which is due to the full-scale genuineness and does not aect aw-
less operation.
All Carrera spare parts are available in the webshop:

Delivery exclusively to Germany, Austria, Netherlands, Belgium and
Luxembourg.
Technical specifications

18 V
54 VA (Carrera DIGITAL 124)
14,8 V 51,8 VA (Carrera DIGITAL 132)

1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED ashes at
long intervals.
By operating the speed controller the stand-by mode is nished,
the racetrack returns to idle-mode again.
4.) O-state = power supply unit disconnected from mains supply
This device is marked by “selective sort throught” symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized “sorting/collecting” sys-
tem in accordance with European directive 2002/96/CE, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are not
going through special collecting, are potentially dangerous for envi-
ronment and human health, because of dangerous substance.

18 V
54 VA (Carrera DIGITAL 124)
14,8 V 51,8 VA (Carrera DIGITAL 132)

1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED ashes at
long intervals.
By operating the speed controller the stand-by mode is nished,
the racetrack returns to idle-mode again.
4.) O-state = power supply unit disconnected from mains supply
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

carrera-digital-124---30352-control-unit

Suche zurücksetzen

  • wie wird der Positions Tower 30357 an den Control Unit 30352 Angemelder oder programiert Eingereicht am 18-9-2017 17:47

    Antworten Frage melden

  • Wie wird der Positions Tower 30357 an den Control Unit 30352 Angemeldet oder programiert Eingereicht am 18-9-2017 17:33

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Carrera Digital 124 - 30352 Control Unit wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info